arch/arm/boot/dts/ste-href.dtsi

   1 // SPDX-License-Identifier: GPL-2.0-or-later
   2 /*
   3  * Copyright 2012 ST-Ericsson AB
   4  */
   5
   6 #include <dt-bindings/interrupt-controller/irq.h>
   7 #include <dt-bindings/leds/common.h>
   8 #include "ste-href-family-pinctrl.dtsi"
   9
  10 / {
  11         memory {
  12                 device_type = "memory";
  13                 reg = <0x00000000 0x20000000>;
  14         };
  15
  16         battery: battery {
  17                 compatible = "simple-battery";
  18                 battery-type = "lithium-ion-polymer";
  19         };
  20
  21         thermal-zones {
  22                 battery-thermal {
  23                         /* This zone will be polled by the battery temperature code */
  24                         polling-delay = <0>;
  25                         polling-delay-passive = <0>;
  26                         thermal-sensors = <&bat_therm>;
  27
  28                         trips {
  29                                 battery-crit-hi {
  30                                         temperature = <70000>;
  31                                         hysteresis = <2000>;
  32                                         type = "critical";
  33                                 };
  34                         };
  35                 };
  36         };
  37
  38         bat_therm: thermistor {
  39                 compatible = "murata,ncp18wb473";
  40                 io-channels = <&gpadc 0x02>; /* BatTemp */
  41                 pullup-uv = <1800000>;
  42                 pullup-ohm = <230000>;
  43                 pulldown-ohm = <0>;
  44                 #thermal-sensor-cells = <0>;
  45         };
  46
  47         soc {
  48                 uart@80120000 {
  49                         pinctrl-names = "default", "sleep";
  50                         pinctrl-0 = <&u0_a_1_default>;
  51                         pinctrl-1 = <&u0_a_1_sleep>;
  52                         status = "okay";
  53                 };
  54
  55                 /* This UART is unused and thus left disabled */
  56                 uart@80121000 {
  57                         pinctrl-names = "default", "sleep";
  58                         pinctrl-0 = <&u1rxtx_a_1_default>;
  59                         pinctrl-1 = <&u1rxtx_a_1_sleep>;
  60                 };
  61
  62                 uart@80007000 {
  63                         pinctrl-names = "default", "sleep";
  64                         pinctrl-0 = <&u2rxtx_c_1_default>;
  65                         pinctrl-1 = <&u2rxtx_c_1_sleep>;
  66                         status = "okay";
  67                 };
  68
  69                 i2c@80004000 {
  70                         pinctrl-names = "default","sleep";
  71                         pinctrl-0 = <&i2c0_a_1_default>;
  72                         pinctrl-1 = <&i2c0_a_1_sleep>;
  73                         status = "okay";
  74                 };
  75
  76                 i2c@80122000 {
  77                         pinctrl-names = "default","sleep";
  78                         pinctrl-0 = <&i2c1_b_2_default>;
  79                         pinctrl-1 = <&i2c1_b_2_sleep>;
  80                         status = "okay";
  81                 };
  82
  83                 i2c@80128000 {
  84                         pinctrl-names = "default","sleep";
  85                         pinctrl-0 = <&i2c2_b_2_default>;
  86                         pinctrl-1 = <&i2c2_b_2_sleep>;
  87                         status = "okay";
  88                         lp5521@33 {
  89                                 compatible = "national,lp5521";
  90                                 reg = <0x33>;
  91                                 label = "lp5521_pri";
  92                                 clock-mode = /bits/ 8 <2>;
  93                                 #address-cells = <1>;
  94                                 #size-cells = <0>;
  95                                 led@0 {
  96                                         reg = <0>;
  97                                         led-cur = /bits/ 8 <0x2f>;
  98                                         max-cur = /bits/ 8 <0x5f>;
  99                                         color = <LED_COLOR_ID_BLUE>;
 100                                         linux,default-trigger = "heartbeat";
 101                                 };
 102                                 led@1 {
 103                                         reg = <1>;
 104                                         led-cur = /bits/ 8 <0x2f>;
 105                                         max-cur = /bits/ 8 <0x5f>;
 106                                         color = <LED_COLOR_ID_BLUE>;
 107                                 };
 108                                 led@2 {
 109                                         reg = <2>;
 110                                         led-cur = /bits/ 8 <0x2f>;
 111                                         max-cur = /bits/ 8 <0x5f>;
 112                                         color = <LED_COLOR_ID_BLUE>;
 113                                 };
 114                         };
 115                         lp5521@34 {
 116                                 compatible = "national,lp5521";
 117                                 reg = <0x34>;
 118                                 label = "lp5521_sec";
 119                                 clock-mode = /bits/ 8 <2>;
 120                                 #address-cells = <1>;
 121                                 #size-cells = <0>;
 122                                 led@0 {
 123                                         reg = <0>;
 124                                         led-cur = /bits/ 8 <0x2f>;
 125                                         max-cur = /bits/ 8 <0x5f>;
 126                                         color = <LED_COLOR_ID_BLUE>;
 127                                 };
 128                                 led@1 {
 129                                         reg = <1>;
 130                                         led-cur = /bits/ 8 <0x2f>;
 131                                         max-cur = /bits/ 8 <0x5f>;
 132                                         color = <LED_COLOR_ID_BLUE>;
 133                                 };
 134                                 led@2 {
 135                                         reg = <2>;
 136                                         led-cur = /bits/ 8 <0x2f>;
 137                                         max-cur = /bits/ 8 <0x5f>;
 138                                         color = <LED_COLOR_ID_BLUE>;
 139                                 };
 140                         };
 141                         bh1780@29 {
 142                                 compatible = "rohm,bh1780gli";
 143                                 reg = <0x29>;
 144                         };
 145                 };
 146
 147                 i2c@80110000 {
 148                         pinctrl-names = "default","sleep";
 149                         pinctrl-0 = <&i2c3_c_2_default>;
 150                         pinctrl-1 = <&i2c3_c_2_sleep>;
 151                         status = "okay";
 152                 };
 153
 154                 // External Micro SD slot
 155                 mmc@80126000 {
 156                         arm,primecell-periphid = <0x10480180>;
 157                         max-frequency = <100000000>;
 158                         bus-width = <4>;
 159                         cap-sd-highspeed;
 160                         cap-mmc-highspeed;
 161                         sd-uhs-sdr12;
 162                         sd-uhs-sdr25;
 163                         full-pwr-cycle;
 164                         st,sig-dir-dat0;
 165                         st,sig-dir-dat2;
 166                         st,sig-dir-cmd;
 167                         st,sig-pin-fbclk;
 168                         vmmc-supply = <&ab8500_ldo_aux3_reg>;
 169                         vqmmc-supply = <&vmmci>;
 170                         pinctrl-names = "default", "sleep";
 171                         pinctrl-0 = <&mc0_a_1_default &sdi0_default_mode>;
 172                         pinctrl-1 = <&mc0_a_1_sleep>;
 173
 174                         status = "okay";
 175                 };
 176
 177                 // WLAN SDIO channel
 178                 mmc@80118000 {
 179                         arm,primecell-periphid = <0x10480180>;
 180                         max-frequency = <100000000>;
 181                         bus-width = <4>;
 182                         non-removable;
 183                         pinctrl-names = "default", "sleep";
 184                         pinctrl-0 = <&mc1_a_1_default>;
 185                         pinctrl-1 = <&mc1_a_1_sleep>;
 186
 187                         status = "okay";
 188                 };
 189
 190                 // PoP:ed eMMC
 191                 mmc@80005000 {
 192                         arm,primecell-periphid = <0x10480180>;
 193                         max-frequency = <100000000>;
 194                         bus-width = <8>;
 195                         cap-mmc-highspeed;
 196                         non-removable;
 197                         no-sdio;
 198                         no-sd;
 199                         vmmc-supply = <&db8500_vsmps2_reg>;
 200                         pinctrl-names = "default", "sleep";
 201                         pinctrl-0 = <&mc2_a_1_default>;
 202                         pinctrl-1 = <&mc2_a_1_sleep>;
 203
 204                         status = "okay";
 205                 };
 206
 207                 // On-board eMMC
 208                 mmc@80114000 {
 209                         arm,primecell-periphid = <0x10480180>;
 210                         max-frequency = <100000000>;
 211                         bus-width = <8>;
 212                         cap-mmc-highspeed;
 213                         non-removable;
 214                         no-sdio;
 215                         no-sd;
 216                         vmmc-supply = <&ab8500_ldo_aux2_reg>;
 217                         pinctrl-names = "default", "sleep";
 218                         pinctrl-0 = <&mc4_a_1_default>;
 219                         pinctrl-1 = <&mc4_a_1_sleep>;
 220
 221                         status = "okay";
 222                 };
 223
 224                 msp0: msp@80123000 {
 225                         pinctrl-names = "default";
 226                         pinctrl-0 = <&msp0txrxtfstck_a_1_default>;
 227                         status = "okay";
 228                 };
 229
 230                 msp1: msp@80124000 {
 231                         pinctrl-names = "default";
 232                         pinctrl-0 = <&msp1txrx_a_1_default>;
 233                         status = "okay";
 234                 };
 235
 236                 msp2: msp@80117000 {
 237                         pinctrl-names = "default";
 238                         pinctrl-0 = <&msp2_a_1_default>;
 239                 };
 240
 241                 msp3: msp@80125000 {
 242                         status = "okay";
 243                 };
 244
 245                 prcmu@80157000 {
 246                         ab8500 {
 247                                 gpio {
 248                                 };
 249
 250                                 phy {
 251                                         pinctrl-names = "default", "sleep";
 252                                         pinctrl-0 = <&usb_a_1_default>;
 253                                         pinctrl-1 = <&usb_a_1_sleep>;
 254                                 };
 255
 256                                 regulator {
 257                                         ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
 258                                                 regulator-name = "V-DISPLAY";
 259                                         };
 260
 261                                         ab8500_ldo_aux2_reg: ab8500_ldo_aux2 {
 262                                                 regulator-name = "V-eMMC1";
 263                                         };
 264
 265                                         ab8500_ldo_aux3_reg: ab8500_ldo_aux3 {
 266                                                 regulator-name = "V-MMC-SD";
 267                                         };
 268
 269                                         ab8500_ldo_intcore_reg: ab8500_ldo_intcore {
 270                                                 regulator-name = "V-INTCORE";
 271                                         };
 272
 273                                         ab8500_ldo_tvout_reg: ab8500_ldo_tvout {
 274                                                 regulator-name = "V-TVOUT";
 275                                         };
 276
 277                                         ab8500_ldo_audio_reg: ab8500_ldo_audio {
 278                                                 regulator-name = "V-AUD";
 279                                         };
 280
 281                                         ab8500_ldo_anamic1_reg: ab8500_ldo_anamic1 {
 282                                                 regulator-name = "V-AMIC1";
 283                                         };
 284
 285                                         ab8500_ldo_anamic2_reg: ab8500_ldo_anamic2 {
 286                                                 regulator-name = "V-AMIC2";
 287                                         };
 288
 289                                         ab8500_ldo_dmic_reg: ab8500_ldo_dmic {
 290                                                 regulator-name = "V-DMIC";
 291                                         };
 292
 293                                         ab8500_ldo_ana_reg: ab8500_ldo_ana {
 294                                                 regulator-name = "V-CSI/DSI";
 295                                         };
 296                                 };
 297                         };
 298                 };
 299
 300                 pinctrl {
 301                         sdi0 {
 302                                 sdi0_default_mode: sdi0_default {
 303                                         /* Some boards set additional settings here */
 304                                 };
 305                         };
 306                 };
 307
 308                 mcde@a0350000 {
 309                         pinctrl-names = "default", "sleep";
 310                         pinctrl-0 = <&lcd_default_mode>;
 311                         pinctrl-1 = <&lcd_sleep_mode>;
 312                 };
 313         };
 314 };