1 // SPDX-License-Identifier: GPL-2.0-only
3 * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
5 * Based on "omap4.dtsi"
8 #include <dt-bindings/bus/ti-sysc.h>
9 #include <dt-bindings/gpio/gpio.h>
10 #include <dt-bindings/interrupt-controller/arm-gic.h>
11 #include <dt-bindings/pinctrl/omap.h>
12 #include <dt-bindings/clock/omap5.h>
18 compatible = "ti,omap5";
19 interrupt-parent = <&wakeupgen>;
42 compatible = "arm,cortex-a15";
51 clocks = <&dpll_mpu_ck>;
54 clock-latency = <300000>; /* From omap-cpufreq driver */
57 #cooling-cells = <2>; /* min followed by max */
61 compatible = "arm,cortex-a15";
70 clocks = <&dpll_mpu_ck>;
73 clock-latency = <300000>; /* From omap-cpufreq driver */
76 #cooling-cells = <2>; /* min followed by max */
81 #include "omap4-cpu-thermal.dtsi"
82 #include "omap5-gpu-thermal.dtsi"
83 #include "omap5-core-thermal.dtsi"
87 compatible = "arm,armv7-timer";
88 /* PPI secure/nonsecure IRQ */
89 interrupts = <GIC_PPI 13 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>,
90 <GIC_PPI 14 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>,
91 <GIC_PPI 11 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>,
92 <GIC_PPI 10 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>;
93 interrupt-parent = <&gic>;
97 compatible = "arm,cortex-a15-pmu";
98 interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
99 <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>;
102 gic: interrupt-controller@48211000 {
103 compatible = "arm,cortex-a15-gic";
104 interrupt-controller;
105 #interrupt-cells = <3>;
106 reg = <0 0x48211000 0 0x1000>,
107 <0 0x48212000 0 0x2000>,
108 <0 0x48214000 0 0x2000>,
109 <0 0x48216000 0 0x2000>;
110 interrupt-parent = <&gic>;
113 wakeupgen: interrupt-controller@48281000 {
114 compatible = "ti,omap5-wugen-mpu", "ti,omap4-wugen-mpu";
115 interrupt-controller;
116 #interrupt-cells = <3>;
117 reg = <0 0x48281000 0 0x1000>;
118 interrupt-parent = <&gic>;
122 * The soc node represents the soc top level view. It is used for IPs
123 * that are not memory mapped in the MPU view or for the MPU itself.
126 compatible = "ti,omap-infra";
128 compatible = "ti,omap4-mpu";
135 * XXX: Use a flat representation of the OMAP3 interconnect.
136 * The real OMAP interconnect network is quite complex.
137 * Since it will not bring real advantage to represent that in DT for
138 * the moment, just use a fake OCP bus entry to represent the whole bus
142 compatible = "ti,omap5-l3-noc", "simple-bus";
143 #address-cells = <1>;
145 ranges = <0 0 0 0xc0000000>;
146 dma-ranges = <0x80000000 0x0 0x80000000 0x80000000>;
147 ti,hwmods = "l3_main_1", "l3_main_2", "l3_main_3";
148 reg = <0 0x44000000 0 0x2000>,
149 <0 0x44800000 0 0x3000>,
150 <0 0x45000000 0 0x4000>;
151 interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
152 <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
154 l4_wkup: interconnect@4ae00000 {
157 l4_cfg: interconnect@4a000000 {
160 l4_per: interconnect@48000000 {
163 l4_abe: interconnect@40100000 {
166 ocmcram: sram@40300000 {
167 compatible = "mmio-sram";
168 reg = <0x40300000 0x20000>; /* 128k */
171 gpmc: gpmc@50000000 {
172 compatible = "ti,omap4430-gpmc";
173 reg = <0x50000000 0x1000>;
174 #address-cells = <2>;
176 interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
180 gpmc,num-waitpins = <4>;
182 clocks = <&l3_iclk_div>;
184 interrupt-controller;
185 #interrupt-cells = <2>;
190 target-module@55082000 {
191 compatible = "ti,sysc-omap2", "ti,sysc";
192 reg = <0x55082000 0x4>,
195 reg-names = "rev", "sysc", "syss";
196 ti,sysc-sidle = <SYSC_IDLE_FORCE>,
199 ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
200 SYSC_OMAP2_SOFTRESET |
201 SYSC_OMAP2_AUTOIDLE)>;
202 clocks = <&ipu_clkctrl OMAP5_MMU_IPU_CLKCTRL 0>;
204 resets = <&prm_core 2>;
205 reset-names = "rstctrl";
206 ranges = <0x0 0x55082000 0x100>;
208 #address-cells = <1>;
211 compatible = "ti,omap4-iommu";
213 interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
215 ti,iommu-bus-err-back;
220 compatible = "ti,omap5-dmm";
221 reg = <0x4e000000 0x800>;
222 interrupts = <0 113 0x4>;
226 emif1: emif@4c000000 {
227 compatible = "ti,emif-4d5";
230 phy-type = <2>; /* DDR PHY type: Intelli PHY */
231 reg = <0x4c000000 0x400>;
232 interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
233 hw-caps-read-idle-ctrl;
234 hw-caps-ll-interface;
238 emif2: emif@4d000000 {
239 compatible = "ti,emif-4d5";
242 phy-type = <2>; /* DDR PHY type: Intelli PHY */
243 reg = <0x4d000000 0x400>;
244 interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
245 hw-caps-read-idle-ctrl;
246 hw-caps-ll-interface;
250 bandgap: bandgap@4a0021e0 {
251 reg = <0x4a0021e0 0xc
255 interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
256 compatible = "ti,omap5430-bandgap";
258 #thermal-sensor-cells = <1>;
262 sata: sata@4a141100 {
263 compatible = "snps,dwc-ahci";
264 reg = <0x4a140000 0x1100>, <0x4a141100 0x7>;
265 interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
267 phy-names = "sata-phy";
268 clocks = <&l3init_clkctrl OMAP5_SATA_CLKCTRL 8>;
270 ports-implemented = <0x1>;
273 target-module@56000000 {
274 compatible = "ti,sysc-omap4", "ti,sysc";
275 reg = <0x5600fe00 0x4>,
277 reg-names = "rev", "sysc";
278 ti,sysc-midle = <SYSC_IDLE_FORCE>,
281 ti,sysc-sidle = <SYSC_IDLE_FORCE>,
284 clocks = <&gpu_clkctrl OMAP5_GPU_CLKCTRL 0>;
286 #address-cells = <1>;
288 ranges = <0 0x56000000 0x2000000>;
291 * Closed source PowerVR driver, no child device
292 * binding or driver in mainline
296 target-module@58000000 {
297 compatible = "ti,sysc-omap2", "ti,sysc";
298 reg = <0x58000000 4>,
300 reg-names = "rev", "syss";
302 clocks = <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 0>,
303 <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 9>,
304 <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 10>,
305 <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 11>;
306 clock-names = "fck", "hdmi_clk", "sys_clk", "tv_clk";
307 #address-cells = <1>;
309 ranges = <0 0x58000000 0x1000000>;
312 compatible = "ti,omap5-dss";
315 clocks = <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 8>;
317 #address-cells = <1>;
319 ranges = <0 0 0x1000000>;
322 compatible = "ti,sysc-omap2", "ti,sysc";
326 reg-names = "rev", "sysc", "syss";
327 ti,sysc-sidle = <SYSC_IDLE_FORCE>,
330 ti,sysc-midle = <SYSC_IDLE_FORCE>,
333 ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
334 SYSC_OMAP2_ENAWAKEUP |
335 SYSC_OMAP2_SOFTRESET |
336 SYSC_OMAP2_AUTOIDLE)>;
338 clocks = <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 8>;
340 #address-cells = <1>;
342 ranges = <0 0x1000 0x1000>;
345 compatible = "ti,omap5-dispc";
347 interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
348 clocks = <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 8>;
354 compatible = "ti,sysc-omap2", "ti,sysc";
358 reg-names = "rev", "sysc", "syss";
359 ti,sysc-sidle = <SYSC_IDLE_FORCE>,
362 ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
363 SYSC_OMAP2_AUTOIDLE)>;
365 clocks = <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 8>;
367 #address-cells = <1>;
369 ranges = <0 0x2000 0x1000>;
372 compatible = "ti,omap5-rfbi";
375 clocks = <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 8>, <&l3_iclk_div>;
376 clock-names = "fck", "ick";
381 compatible = "ti,sysc-omap2", "ti,sysc";
385 reg-names = "rev", "sysc", "syss";
386 ti,sysc-sidle = <SYSC_IDLE_FORCE>,
389 ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
390 SYSC_OMAP2_ENAWAKEUP |
391 SYSC_OMAP2_SOFTRESET |
392 SYSC_OMAP2_AUTOIDLE)>;
394 #address-cells = <1>;
396 ranges = <0 0x5000 0x1000>;
399 compatible = "ti,omap5-dsi";
403 reg-names = "proto", "phy", "pll";
404 interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
406 clocks = <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 8>;
412 compatible = "ti,sysc-omap2", "ti,sysc";
416 reg-names = "rev", "sysc", "syss";
417 ti,sysc-sidle = <SYSC_IDLE_FORCE>,
420 ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
421 SYSC_OMAP2_ENAWAKEUP |
422 SYSC_OMAP2_SOFTRESET |
423 SYSC_OMAP2_AUTOIDLE)>;
425 #address-cells = <1>;
427 ranges = <0 0x9000 0x1000>;
430 compatible = "ti,omap5-dsi";
434 reg-names = "proto", "phy", "pll";
435 interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
437 clocks = <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 8>;
442 target-module@40000 {
443 compatible = "ti,sysc-omap4", "ti,sysc";
446 reg-names = "rev", "sysc";
447 ti,sysc-sidle = <SYSC_IDLE_FORCE>,
450 <SYSC_IDLE_SMART_WKUP>;
451 ti,sysc-mask = <(SYSC_OMAP4_SOFTRESET)>;
452 clocks = <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 9>,
453 <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 8>;
454 clock-names = "fck", "dss_clk";
455 #address-cells = <1>;
457 ranges = <0 0x40000 0x40000>;
460 compatible = "ti,omap5-hdmi";
465 reg-names = "wp", "pll", "phy", "core";
466 interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
468 clocks = <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 9>,
469 <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 10>;
470 clock-names = "fck", "sys_clk";
472 dma-names = "audio_tx";
478 abb_mpu: regulator-abb-mpu {
479 compatible = "ti,abb-v2";
480 regulator-name = "abb_mpu";
481 #address-cells = <0>;
483 clocks = <&sys_clkin>;
484 ti,settling-time = <50>;
485 ti,clock-cycles = <16>;
487 reg = <0x4ae07cdc 0x8>, <0x4ae06014 0x4>,
488 <0x4a0021c4 0x8>, <0x4ae0c318 0x4>;
489 reg-names = "base-address", "int-address",
490 "efuse-address", "ldo-address";
491 ti,tranxdone-status-mask = <0x80>;
492 /* LDOVBBMPU_MUX_CTRL */
493 ti,ldovbb-override-mask = <0x400>;
494 /* LDOVBBMPU_VSET_OUT */
495 ti,ldovbb-vset-mask = <0x1F>;
498 * NOTE: only FBB mode used but actual vset will
499 * determine final biasing
502 /*uV ABB efuse rbb_m fbb_m vset_m*/
503 1060000 0 0x0 0 0x02000000 0x01F00000
504 1250000 0 0x4 0 0x02000000 0x01F00000
508 abb_mm: regulator-abb-mm {
509 compatible = "ti,abb-v2";
510 regulator-name = "abb_mm";
511 #address-cells = <0>;
513 clocks = <&sys_clkin>;
514 ti,settling-time = <50>;
515 ti,clock-cycles = <16>;
517 reg = <0x4ae07ce4 0x8>, <0x4ae06010 0x4>,
518 <0x4a0021a4 0x8>, <0x4ae0c314 0x4>;
519 reg-names = "base-address", "int-address",
520 "efuse-address", "ldo-address";
521 ti,tranxdone-status-mask = <0x80000000>;
522 /* LDOVBBMM_MUX_CTRL */
523 ti,ldovbb-override-mask = <0x400>;
524 /* LDOVBBMM_VSET_OUT */
525 ti,ldovbb-vset-mask = <0x1F>;
528 * NOTE: only FBB mode used but actual vset will
529 * determine final biasing
532 /*uV ABB efuse rbb_m fbb_m vset_m*/
533 1025000 0 0x0 0 0x02000000 0x01F00000
534 1120000 0 0x4 0 0x02000000 0x01F00000
541 polling-delay = <500>; /* milliseconds */
542 coefficients = <65 (-1791)>;
545 #include "omap5-l4.dtsi"
546 #include "omap54xx-clocks.dtsi"
549 coefficients = <117 (-2992)>;
553 coefficients = <0 2000>;
556 #include "omap5-l4-abe.dtsi"
557 #include "omap54xx-clocks.dtsi"
561 compatible = "ti,omap5-prm-inst", "ti,omap-prm-inst";
567 compatible = "ti,omap5-prm-inst", "ti,omap-prm-inst";
573 compatible = "ti,omap5-prm-inst", "ti,omap-prm-inst";
574 reg = <0x1200 0x100>;
578 prm_device: prm@1c00 {
579 compatible = "ti,omap5-prm-inst", "ti,omap-prm-inst";
580 reg = <0x1c00 0x100>;