arch/arm/boot/dts/motorola-mapphone-common.dtsi

   1 // SPDX-License-Identifier: GPL-2.0-only
   2 /dts-v1/;
   3
   4 #include <dt-bindings/input/input.h>
   5 #include "omap443x.dtsi"
   6 #include "motorola-cpcap-mapphone.dtsi"
   7
   8 / {
   9         chosen {
  10                 stdout-path = &uart3;
  11         };
  12
  13         aliases {
  14                 display0 = &lcd0;
  15                 display1 = &hdmi0;
  16         };
  17
  18         /*
  19          * We seem to have only 1021 MB accessible, 1021 - 1022 is locked,
  20          * then 1023 - 1024 seems to contain mbm.
  21          */
  22         memory {
  23                 device_type = "memory";
  24                 reg = <0x80000000 0x3fd00000>;  /* 1021 MB */
  25         };
  26
  27         /* Poweroff GPIO probably connected to CPCAP */
  28         gpio-poweroff {
  29                 compatible = "gpio-poweroff";
  30                 pinctrl-0 = <&poweroff_gpio>;
  31                 pinctrl-names = "default";
  32                 gpios = <&gpio2 18 GPIO_ACTIVE_LOW>;    /* gpio50 */
  33         };
  34
  35         hdmi0: connector {
  36                 compatible = "hdmi-connector";
  37                 pinctrl-0 = <&hdmi_hpd_gpio>;
  38                 pinctrl-names = "default";
  39                 label = "hdmi";
  40                 type = "d";
  41
  42                 hpd-gpios = <&gpio2 31 GPIO_ACTIVE_HIGH>;       /* gpio63 */
  43
  44                 port {
  45                         hdmi_connector_in: endpoint {
  46                                 remote-endpoint = <&hdmi_out>;
  47                         };
  48                 };
  49         };
  50
  51         /*
  52          * HDMI 5V regulator probably sourced from battery. Let's keep
  53          * keep this as always enabled for HDMI to work until we've
  54          * figured what the encoder chip is.
  55          */
  56         hdmi_regulator: regulator-hdmi {
  57                 compatible = "regulator-fixed";
  58                 regulator-name = "hdmi";
  59                 regulator-min-microvolt = <5000000>;
  60                 regulator-max-microvolt = <5000000>;
  61                 gpio = <&gpio2 27 GPIO_ACTIVE_HIGH>;    /* gpio59 */
  62                 enable-active-high;
  63                 regulator-always-on;
  64         };
  65
  66         /* FS USB Host PHY on port 1 for mdm6600 */
  67         fsusb1_phy: usb-phy@1 {
  68                 compatible = "motorola,mapphone-mdm6600";
  69                 pinctrl-0 = <&usb_mdm6600_pins>;
  70                 pinctrl-names = "default";
  71                 enable-gpios = <&gpio3 31 GPIO_ACTIVE_LOW>;     /* gpio_95 */
  72                 power-gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>;     /* gpio_54 */
  73                 reset-gpios = <&gpio2 17 GPIO_ACTIVE_HIGH>;     /* gpio_49 */
  74                 /* mode: gpio_148 gpio_149 */
  75                 motorola,mode-gpios = <&gpio5 20 GPIO_ACTIVE_HIGH>,
  76                                       <&gpio5 21 GPIO_ACTIVE_HIGH>;
  77                 /* cmd: gpio_103 gpio_104 gpio_142 */
  78                 motorola,cmd-gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>,
  79                                      <&gpio4 8 GPIO_ACTIVE_HIGH>,
  80                                      <&gpio5 14 GPIO_ACTIVE_HIGH>;
  81                 /* status: gpio_52 gpio_53 gpio_55 */
  82                 motorola,status-gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>,
  83                                         <&gpio2 21 GPIO_ACTIVE_HIGH>,
  84                                         <&gpio2 23 GPIO_ACTIVE_HIGH>;
  85                 #phy-cells = <0>;
  86         };
  87
  88         /* HS USB host TLL nop-phy on port 2 for w3glte */
  89         hsusb2_phy: usb-phy@2 {
  90                 compatible = "usb-nop-xceiv";
  91                 #phy-cells = <0>;
  92         };
  93
  94         /* LCD regulator from sw5 source */
  95         lcd_regulator: regulator-lcd {
  96                 compatible = "regulator-fixed";
  97                 regulator-name = "lcd";
  98                 regulator-min-microvolt = <5050000>;
  99                 regulator-max-microvolt = <5050000>;
 100                 gpio = <&gpio4 0 GPIO_ACTIVE_HIGH>;     /* gpio96 */
 101                 enable-active-high;
 102                 vin-supply = <&sw5>;
 103         };
 104
 105         /* This is probably coming straight from the battery.. */
 106         wl12xx_vmmc: regulator-wl12xx {
 107                 compatible = "regulator-fixed";
 108                 regulator-name = "vwl1271";
 109                 regulator-min-microvolt = <1650000>;
 110                 regulator-max-microvolt = <1650000>;
 111                 gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>;    /* gpio94 */
 112                 startup-delay-us = <70000>;
 113                 enable-active-high;
 114         };
 115
 116         gpio_keys {
 117                 compatible = "gpio-keys";
 118
 119                 volume_down {
 120                         label = "Volume Down";
 121                         gpios = <&gpio5 26 GPIO_ACTIVE_LOW>; /* gpio154 */
 122                         linux,code = <KEY_VOLUMEDOWN>;
 123                         linux,can-disable;
 124                         /* Value above 7.95ms for no GPIO hardware debounce */
 125                         debounce-interval = <10>;
 126                 };
 127
 128                 slider {
 129                         label = "Keypad Slide";
 130                         gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>; /* gpio122 */
 131                         linux,input-type = <EV_SW>;
 132                         linux,code = <SW_KEYPAD_SLIDE>;
 133                         linux,can-disable;
 134                         /* Value above 7.95ms for no GPIO hardware debounce */
 135                         debounce-interval = <10>;
 136                 };
 137         };
 138
 139         soundcard {
 140                 compatible = "audio-graph-card";
 141                 label = "Droid 4 Audio";
 142
 143                 simple-graph-card,widgets =
 144                         "Speaker", "Earpiece",
 145                         "Speaker", "Loudspeaker",
 146                         "Headphone", "Headphone Jack",
 147                         "Microphone", "Internal Mic";
 148
 149                 simple-graph-card,routing =
 150                         "Earpiece", "EP",
 151                         "Loudspeaker", "SPKR",
 152                         "Headphone Jack", "HSL",
 153                         "Headphone Jack", "HSR",
 154                         "MICR", "Internal Mic";
 155
 156                 dais = <&mcbsp2_port>, <&mcbsp3_port>;
 157         };
 158
 159         pwm8: dmtimer-pwm-8 {
 160                 pinctrl-names = "default";
 161                 pinctrl-0 = <&vibrator_direction_pin>;
 162
 163                 compatible = "ti,omap-dmtimer-pwm";
 164                 #pwm-cells = <3>;
 165                 ti,timers = <&timer8>;
 166                 ti,clock-source = <0x01>;
 167         };
 168
 169         pwm9: dmtimer-pwm-9 {
 170                 pinctrl-names = "default";
 171                 pinctrl-0 = <&vibrator_enable_pin>;
 172
 173                 compatible = "ti,omap-dmtimer-pwm";
 174                 #pwm-cells = <3>;
 175                 ti,timers = <&timer9>;
 176                 ti,clock-source = <0x01>;
 177         };
 178
 179         vibrator {
 180                 compatible = "pwm-vibrator";
 181                 pwms = <&pwm9 0 10000000 0>, <&pwm8 0 10000000 0>;
 182                 pwm-names = "enable", "direction";
 183                 direction-duty-cycle-ns = <10000000>;
 184         };
 185
 186         backlight: backlight {
 187                 compatible = "led-backlight";
 188
 189                 leds = <&backlight_led>;
 190                 brightness-levels = <31 63 95 127 159 191 223 255>;
 191                 default-brightness-level = <6>;
 192         };
 193 };
 194
 195 &dss {
 196         status = "okay";
 197 };
 198
 199 &dsi1 {
 200         status = "okay";
 201         vdd-supply = <&vcsi>;
 202
 203         port {
 204                 dsi1_out_ep: endpoint {
 205                         remote-endpoint = <&lcd0_in>;
 206                         lanes = <0 1 2 3 4 5>;
 207                 };
 208         };
 209
 210         lcd0: display {
 211                 compatible = "panel-dsi-cm";
 212                 label = "lcd0";
 213                 vddi-supply = <&lcd_regulator>;
 214                 reset-gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>;      /* gpio101 */
 215
 216                 backlight = <&backlight>;
 217
 218                 width-mm = <50>;
 219                 height-mm = <89>;
 220
 221                 panel-timing {
 222                         clock-frequency = <0>;          /* Calculated by dsi */
 223
 224                         hback-porch = <2>;
 225                         hactive = <540>;
 226                         hfront-porch = <0>;
 227                         hsync-len = <2>;
 228
 229                         vback-porch = <1>;
 230                         vactive = <960>;
 231                         vfront-porch = <0>;
 232                         vsync-len = <1>;
 233
 234                         hsync-active = <0>;
 235                         vsync-active = <0>;
 236                         de-active = <1>;
 237                         pixelclk-active = <1>;
 238                 };
 239
 240                 port {
 241                         lcd0_in: endpoint {
 242                                 remote-endpoint = <&dsi1_out_ep>;
 243                         };
 244                 };
 245         };
 246 };
 247
 248 &hdmi {
 249         status = "okay";
 250         pinctrl-0 = <&dss_hdmi_pins>;
 251         pinctrl-names = "default";
 252         vdda-supply = <&vdac>;
 253
 254         port {
 255                 hdmi_out: endpoint {
 256                         remote-endpoint = <&hdmi_connector_in>;
 257                         lanes = <1 0 3 2 5 4 7 6>;
 258                 };
 259         };
 260 };
 261
 262 /* Battery NVRAM on 1-wire handled by w1_ds250x driver */
 263 &hdqw1w {
 264         pinctrl-0 = <&hdq_pins>;
 265         pinctrl-names = "default";
 266         ti,mode = "1w";
 267 };
 268
 269 &i2c1 {
 270         tmp105@48 {
 271                 compatible = "ti,tmp105";
 272                 reg = <0x48>;
 273                 pinctrl-0 = <&tmp105_irq>;
 274                 pinctrl-names = "default";
 275                 /* kpd_row0.gpio_178 */
 276                 interrupts-extended = <&gpio6 18 IRQ_TYPE_EDGE_FALLING
 277                                        &omap4_pmx_core 0x14e>;
 278                 interrupt-names = "irq", "wakeup";
 279                 wakeup-source;
 280         };
 281 };
 282
 283 &keypad {
 284         keypad,num-rows = <8>;
 285         keypad,num-columns = <8>;
 286         linux,keymap = <
 287
 288         /* Row 1 */
 289         MATRIX_KEY(0, 2, KEY_1)
 290         MATRIX_KEY(0, 6, KEY_2)
 291         MATRIX_KEY(2, 3, KEY_3)
 292         MATRIX_KEY(0, 7, KEY_4)
 293         MATRIX_KEY(0, 4, KEY_5)
 294         MATRIX_KEY(5, 5, KEY_6)
 295         MATRIX_KEY(0, 1, KEY_7)
 296         MATRIX_KEY(0, 5, KEY_8)
 297         MATRIX_KEY(0, 0, KEY_9)
 298         MATRIX_KEY(1, 6, KEY_0)
 299
 300         /* Row 2 */
 301         MATRIX_KEY(3, 4, KEY_APOSTROPHE)
 302         MATRIX_KEY(7, 6, KEY_Q)
 303         MATRIX_KEY(7, 7, KEY_W)
 304         MATRIX_KEY(7, 2, KEY_E)
 305         MATRIX_KEY(1, 0, KEY_R)
 306         MATRIX_KEY(4, 4, KEY_T)
 307         MATRIX_KEY(1, 2, KEY_Y)
 308         MATRIX_KEY(6, 7, KEY_U)
 309         MATRIX_KEY(2, 2, KEY_I)
 310         MATRIX_KEY(5, 6, KEY_O)
 311         MATRIX_KEY(3, 7, KEY_P)
 312         MATRIX_KEY(6, 5, KEY_BACKSPACE)
 313
 314         /* Row 3 */
 315         MATRIX_KEY(5, 4, KEY_TAB)
 316         MATRIX_KEY(5, 7, KEY_A)
 317         MATRIX_KEY(2, 7, KEY_S)
 318         MATRIX_KEY(7, 0, KEY_D)
 319         MATRIX_KEY(2, 6, KEY_F)
 320         MATRIX_KEY(6, 2, KEY_G)
 321         MATRIX_KEY(6, 6, KEY_H)
 322         MATRIX_KEY(1, 4, KEY_J)
 323         MATRIX_KEY(3, 1, KEY_K)
 324         MATRIX_KEY(2, 1, KEY_L)
 325         MATRIX_KEY(4, 6, KEY_ENTER)
 326
 327         /* Row 4 */
 328         MATRIX_KEY(3, 6, KEY_LEFTSHIFT)         /* KEY_CAPSLOCK */
 329         MATRIX_KEY(6, 1, KEY_Z)
 330         MATRIX_KEY(7, 4, KEY_X)
 331         MATRIX_KEY(5, 1, KEY_C)
 332         MATRIX_KEY(1, 7, KEY_V)
 333         MATRIX_KEY(2, 4, KEY_B)
 334         MATRIX_KEY(4, 1, KEY_N)
 335         MATRIX_KEY(1, 1, KEY_M)
 336         MATRIX_KEY(3, 5, KEY_COMMA)
 337         MATRIX_KEY(5, 2, KEY_DOT)
 338         MATRIX_KEY(6, 3, KEY_UP)
 339         MATRIX_KEY(7, 3, KEY_OK)
 340
 341         /* Row 5 */
 342         MATRIX_KEY(2, 5, KEY_LEFTCTRL)          /* KEY_LEFTSHIFT */
 343         MATRIX_KEY(4, 5, KEY_LEFTALT)           /* SYM */
 344         MATRIX_KEY(6, 0, KEY_MINUS)
 345         MATRIX_KEY(4, 7, KEY_EQUAL)
 346         MATRIX_KEY(1, 5, KEY_SPACE)
 347         MATRIX_KEY(3, 2, KEY_SLASH)
 348         MATRIX_KEY(4, 3, KEY_LEFT)
 349         MATRIX_KEY(5, 3, KEY_DOWN)
 350         MATRIX_KEY(3, 3, KEY_RIGHT)
 351
 352         /* Side buttons, KEY_VOLUMEDOWN and KEY_PWER are on CPCAP? */
 353         MATRIX_KEY(5, 0, KEY_VOLUMEUP)
 354         >;
 355 };
 356
 357 &mmc1 {
 358         vmmc-supply = <&vwlan2>;
 359         bus-width = <4>;
 360         cd-gpios = <&gpio6 16 GPIO_ACTIVE_LOW>; /* gpio176 */
 361 };
 362
 363 &mmc2 {
 364         vmmc-supply = <&vsdio>;
 365         bus-width = <8>;
 366         ti,non-removable;
 367 };
 368
 369 &mmc3 {
 370         pinctrl-names = "default";
 371         pinctrl-0 = <&mmc3_pins>;
 372         vmmc-supply = <&wl12xx_vmmc>;
 373         /* uart2_tx.sdmmc3_dat1 pad as wakeirq */
 374         interrupts-extended = <&wakeupgen GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH
 375                                &omap4_pmx_core 0xde>;
 376         interrupt-names = "irq", "wakeup";
 377         non-removable;
 378         bus-width = <4>;
 379         cap-power-off-card;
 380         keep-power-in-suspend;
 381
 382         #address-cells = <1>;
 383         #size-cells = <0>;
 384         wlcore: wlcore@2 {
 385                 compatible = "ti,wl1285", "ti,wl1283";
 386                 reg = <2>;
 387                 /* gpio_100 with gpmc_wait2 pad as wakeirq */
 388                 interrupts-extended = <&gpio4 4 IRQ_TYPE_LEVEL_HIGH>,
 389                                       <&omap4_pmx_core 0x4e>;
 390                 interrupt-names = "irq", "wakeup";
 391                 ref-clock-frequency = <26000000>;
 392                 tcxo-clock-frequency = <26000000>;
 393         };
 394 };
 395
 396 &i2c1 {
 397         led-controller@38 {
 398                 compatible = "ti,lm3532";
 399                 #address-cells = <1>;
 400                 #size-cells = <0>;
 401                 reg = <0x38>;
 402
 403                 enable-gpios = <&gpio6 12 GPIO_ACTIVE_HIGH>;
 404
 405                 ramp-up-us = <1024>;
 406                 ramp-down-us = <8193>;
 407
 408                 backlight_led: led@0 {
 409                         reg = <0>;
 410                         led-sources = <2>;
 411                         ti,led-mode = <0>;
 412                         label = ":backlight";
 413                 };
 414
 415                 led@1 {
 416                         reg = <1>;
 417                         led-sources = <1>;
 418                         ti,led-mode = <0>;
 419                         label = ":kbd_backlight";
 420                 };
 421         };
 422 };
 423
 424 &i2c2 {
 425         touchscreen@4a {
 426                 compatible = "atmel,maxtouch";
 427                 reg = <0x4a>;
 428                 pinctrl-names = "default";
 429                 pinctrl-0 = <&touchscreen_pins>;
 430
 431                 reset-gpios = <&gpio6 13 GPIO_ACTIVE_HIGH>; /* gpio173 */
 432
 433                 /* gpio_183 with sys_nirq2 pad as wakeup */
 434                 interrupts-extended = <&gpio6 23 IRQ_TYPE_LEVEL_LOW>,
 435                                       <&omap4_pmx_core 0x160>;
 436                 interrupt-names = "irq", "wakeup";
 437                 wakeup-source;
 438         };
 439
 440         isl29030@44 {
 441                 compatible = "isil,isl29030";
 442                 reg = <0x44>;
 443
 444                 pinctrl-names = "default";
 445                 pinctrl-0 = <&als_proximity_pins>;
 446
 447                 interrupt-parent = <&gpio6>;
 448                 interrupts = <17 IRQ_TYPE_LEVEL_LOW>; /* gpio177 */
 449         };
 450 };
 451
 452 &omap4_pmx_core {
 453
 454         /* hdmi_hpd.gpio_63 */
 455         hdmi_hpd_gpio: pinmux_hdmi_hpd_pins {
 456                 pinctrl-single,pins = <
 457                 OMAP4_IOPAD(0x098, PIN_INPUT | MUX_MODE3)
 458                 >;
 459         };
 460
 461         hdq_pins: pinmux_hdq_pins {
 462                 pinctrl-single,pins = <
 463                 /* 0x4a100120 hdq_sio.hdq_sio aa27 */
 464                 OMAP4_IOPAD(0x120, PIN_INPUT | MUX_MODE0)
 465                 >;
 466         };
 467
 468         /* hdmi_cec.hdmi_cec, hdmi_scl.hdmi_scl, hdmi_sda.hdmi_sda */
 469         dss_hdmi_pins: pinmux_dss_hdmi_pins {
 470                 pinctrl-single,pins = <
 471                 OMAP4_IOPAD(0x09a, PIN_INPUT | MUX_MODE0)
 472                 OMAP4_IOPAD(0x09c, PIN_INPUT | MUX_MODE0)
 473                 OMAP4_IOPAD(0x09e, PIN_INPUT | MUX_MODE0)
 474                 >;
 475         };
 476
 477         /*
 478          * Android uses PIN_OFF_INPUT_PULLDOWN | PIN_INPUT_PULLUP | MUX_MODE3
 479          * for gpio_100, but the internal pull makes wlan flakey on some
 480          * devices. Off mode value should be tested if we have off mode working
 481          * later on.
 482          */
 483         mmc3_pins: pinmux_mmc3_pins {
 484                 pinctrl-single,pins = <
 485                 /* 0x4a10008e gpmc_wait2.gpio_100 d23 */
 486                 OMAP4_IOPAD(0x08e, PIN_INPUT | MUX_MODE3)
 487
 488                 /* 0x4a100102 abe_mcbsp1_dx.sdmmc3_dat2 ab25 */
 489                 OMAP4_IOPAD(0x102, PIN_INPUT_PULLUP | MUX_MODE1)
 490
 491                 /* 0x4a100104 abe_mcbsp1_fsx.sdmmc3_dat3 ac27 */
 492                 OMAP4_IOPAD(0x104, PIN_INPUT_PULLUP | MUX_MODE1)
 493
 494                 /* 0x4a100118 uart2_cts.sdmmc3_clk ab26 */
 495                 OMAP4_IOPAD(0x118, PIN_INPUT | MUX_MODE1)
 496
 497                 /* 0x4a10011a uart2_rts.sdmmc3_cmd ab27 */
 498                 OMAP4_IOPAD(0x11a, PIN_INPUT_PULLUP | MUX_MODE1)
 499
 500                 /* 0x4a10011c uart2_rx.sdmmc3_dat0 aa25 */
 501                 OMAP4_IOPAD(0x11c, PIN_INPUT_PULLUP | MUX_MODE1)
 502
 503                 /* 0x4a10011e uart2_tx.sdmmc3_dat1 aa26 */
 504                 OMAP4_IOPAD(0x11e, PIN_INPUT_PULLUP | MUX_MODE1)
 505                 >;
 506         };
 507
 508         /* gpmc_ncs0.gpio_50 */
 509         poweroff_gpio: pinmux_poweroff_pins {
 510                 pinctrl-single,pins = <
 511                 OMAP4_IOPAD(0x074, PIN_OUTPUT_PULLUP | MUX_MODE3)
 512                 >;
 513         };
 514
 515         /* kpd_row0.gpio_178 */
 516         tmp105_irq: pinmux_tmp105_irq {
 517                 pinctrl-single,pins = <
 518                 OMAP4_IOPAD(0x18e, PIN_INPUT_PULLUP | MUX_MODE3)
 519                 >;
 520         };
 521
 522         usb_gpio_mux_sel1: pinmux_usb_gpio_mux_sel1_pins {
 523                 /* gpio_60 */
 524                 pinctrl-single,pins = <
 525                 OMAP4_IOPAD(0x088, PIN_OUTPUT | MUX_MODE3)
 526                 >;
 527         };
 528
 529         touchscreen_pins: pinmux_touchscreen_pins {
 530                 pinctrl-single,pins = <
 531                 OMAP4_IOPAD(0x180, PIN_OUTPUT | MUX_MODE3)
 532                 OMAP4_IOPAD(0x1a0, PIN_INPUT_PULLUP | MUX_MODE3)
 533                 >;
 534         };
 535
 536         als_proximity_pins: pinmux_als_proximity_pins {
 537                 pinctrl-single,pins = <
 538                 OMAP4_IOPAD(0x18c, PIN_INPUT_PULLUP | MUX_MODE3)
 539                 >;
 540         };
 541
 542         usb_mdm6600_pins: pinmux_usb_mdm6600_pins {
 543                 pinctrl-single,pins = <
 544                 /* enable 0x4a1000d8 usbb1_ulpitll_dat7.gpio_95 ag16 */
 545                 OMAP4_IOPAD(0x0d8, PIN_INPUT | MUX_MODE3)
 546
 547                 /* power 0x4a10007c gpmc_nwp.gpio_54 c25 */
 548                 OMAP4_IOPAD(0x07c, PIN_OUTPUT | MUX_MODE3)
 549
 550                 /* reset 0x4a100072 gpmc_a25.gpio_49 d20 */
 551                 OMAP4_IOPAD(0x072, PIN_OUTPUT | MUX_MODE3)
 552
 553                 /* mode0/bpwake 0x4a10014e sdmmc5_dat1.gpio_148 af4 */
 554                 OMAP4_IOPAD(0x14e, PIN_OUTPUT | MUX_MODE3)
 555
 556                 /* mode1/apwake 0x4a100150 sdmmc5_dat2.gpio_149 ag3 */
 557                 OMAP4_IOPAD(0x150, PIN_OFF_OUTPUT_LOW | PIN_INPUT | MUX_MODE3)
 558
 559                 /* status0 0x4a10007e gpmc_clk.gpio_55 b22 */
 560                 OMAP4_IOPAD(0x07e, PIN_INPUT | MUX_MODE3)
 561
 562                 /* status1 0x4a10007a gpmc_ncs3.gpio_53 c22 */
 563                 OMAP4_IOPAD(0x07a, PIN_INPUT | MUX_MODE3)
 564
 565                 /* status2 0x4a100078 gpmc_ncs2.gpio_52 d21 */
 566                 OMAP4_IOPAD(0x078, PIN_INPUT | MUX_MODE3)
 567
 568                 /* cmd0 0x4a100094 gpmc_ncs6.gpio_103 c24 */
 569                 OMAP4_IOPAD(0x094, PIN_OUTPUT | MUX_MODE3)
 570
 571                 /* cmd1 0x4a100096 gpmc_ncs7.gpio_104 d24 */
 572                 OMAP4_IOPAD(0x096, PIN_OUTPUT | MUX_MODE3)
 573
 574                 /* cmd2 0x4a100142 uart3_rts_sd.gpio_142 f28 */
 575                 OMAP4_IOPAD(0x142, PIN_OUTPUT | MUX_MODE3)
 576                 >;
 577         };
 578
 579         usb_ulpi_pins: pinmux_usb_ulpi_pins {
 580                 pinctrl-single,pins = <
 581                 OMAP4_IOPAD(0x196, MUX_MODE7)
 582                 OMAP4_IOPAD(0x198, MUX_MODE7)
 583                 OMAP4_IOPAD(0x1b2, PIN_INPUT_PULLUP | MUX_MODE0)
 584                 OMAP4_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE0)
 585                 OMAP4_IOPAD(0x1b6, PIN_INPUT_PULLUP | MUX_MODE0)
 586                 OMAP4_IOPAD(0x1b8, PIN_INPUT_PULLUP | MUX_MODE0)
 587                 OMAP4_IOPAD(0x1ba, PIN_INPUT_PULLUP | MUX_MODE0)
 588                 OMAP4_IOPAD(0x1bc, PIN_INPUT_PULLUP | MUX_MODE0)
 589                 OMAP4_IOPAD(0x1be, PIN_INPUT_PULLUP | MUX_MODE0)
 590                 OMAP4_IOPAD(0x1c0, PIN_INPUT_PULLUP | MUX_MODE0)
 591                 OMAP4_IOPAD(0x1c2, PIN_INPUT_PULLUP | MUX_MODE0)
 592                 OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE0)
 593                 OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE0)
 594                 OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE0)
 595                 >;
 596         };
 597
 598         /* usb0_otg_dp and usb0_otg_dm */
 599         usb_utmi_pins: pinmux_usb_utmi_pins {
 600                 pinctrl-single,pins = <
 601                 OMAP4_IOPAD(0x196, PIN_INPUT | MUX_MODE0)
 602                 OMAP4_IOPAD(0x198, PIN_INPUT | MUX_MODE0)
 603                 OMAP4_IOPAD(0x1b2, PIN_INPUT_PULLUP | MUX_MODE7)
 604                 OMAP4_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE7)
 605                 OMAP4_IOPAD(0x1b6, PIN_INPUT_PULLUP | MUX_MODE7)
 606                 OMAP4_IOPAD(0x1b8, PIN_INPUT_PULLUP | MUX_MODE7)
 607                 OMAP4_IOPAD(0x1ba, PIN_INPUT_PULLUP | MUX_MODE7)
 608                 OMAP4_IOPAD(0x1bc, PIN_INPUT_PULLUP | MUX_MODE7)
 609                 OMAP4_IOPAD(0x1be, PIN_INPUT_PULLUP | MUX_MODE7)
 610                 OMAP4_IOPAD(0x1c0, PIN_INPUT_PULLUP | MUX_MODE7)
 611                 OMAP4_IOPAD(0x1c2, PIN_INPUT_PULLUP | MUX_MODE7)
 612                 OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE7)
 613                 OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE7)
 614                 OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE7)
 615                 >;
 616         };
 617
 618         /*
 619          * Note that the v3.0.8 stock userspace dynamically remuxes uart1
 620          * rts pin probably for PM purposes to PIN_INPUT_PULLUP | MUX_MODE7
 621          * when not used. If needed, we can add rts pin remux later based
 622          * on power measurements.
 623          */
 624         uart1_pins: pinmux_uart1_pins {
 625                 pinctrl-single,pins = <
 626                 /* 0x4a10013c mcspi1_cs2.uart1_cts ag23 */
 627                 OMAP4_IOPAD(0x13c, PIN_INPUT_PULLUP | MUX_MODE1)
 628
 629                 /* 0x4a10013e mcspi1_cs3.uart1_rts ah23 */
 630                 OMAP4_IOPAD(0x13e, MUX_MODE1)
 631
 632                 /* 0x4a100140 uart3_cts_rctx.uart1_tx f27 */
 633                 OMAP4_IOPAD(0x140, PIN_OUTPUT | MUX_MODE1)
 634
 635                 /* 0x4a1001ca dpm_emu14.uart1_rx aa3 */
 636                 OMAP4_IOPAD(0x1ca, PIN_INPUT_PULLUP | MUX_MODE2)
 637                 >;
 638         };
 639
 640         /* uart3_tx_irtx and uart3_rx_irrx */
 641         uart3_pins: pinmux_uart3_pins {
 642                 pinctrl-single,pins = <
 643                 OMAP4_IOPAD(0x196, MUX_MODE7)
 644                 OMAP4_IOPAD(0x198, MUX_MODE7)
 645                 OMAP4_IOPAD(0x1b2, PIN_INPUT_PULLUP | MUX_MODE7)
 646                 OMAP4_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE7)
 647                 OMAP4_IOPAD(0x1b6, PIN_INPUT_PULLUP | MUX_MODE7)
 648                 OMAP4_IOPAD(0x1b8, PIN_INPUT_PULLUP | MUX_MODE7)
 649                 OMAP4_IOPAD(0x1ba, MUX_MODE2)
 650                 OMAP4_IOPAD(0x1bc, PIN_INPUT | MUX_MODE2)
 651                 OMAP4_IOPAD(0x1be, PIN_INPUT_PULLUP | MUX_MODE7)
 652                 OMAP4_IOPAD(0x1c0, PIN_INPUT_PULLUP | MUX_MODE7)
 653                 OMAP4_IOPAD(0x1c2, PIN_INPUT_PULLUP | MUX_MODE7)
 654                 OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE7)
 655                 OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE7)
 656                 OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE7)
 657                 >;
 658         };
 659
 660         uart4_pins: pinmux_uart4_pins {
 661                 pinctrl-single,pins = <
 662                 OMAP4_IOPAD(0x15c, PIN_INPUT | MUX_MODE0)               /* uart4_rx */
 663                 OMAP4_IOPAD(0x15e, PIN_OUTPUT | MUX_MODE0)              /* uart4_tx */
 664                 OMAP4_IOPAD(0x110, PIN_INPUT_PULLUP | MUX_MODE5)        /* uart4_cts */
 665                 OMAP4_IOPAD(0x112, PIN_OUTPUT_PULLUP | MUX_MODE5)       /* uart4_rts */
 666                 >;
 667         };
 668
 669         mcbsp2_pins: pinmux_mcbsp2_pins {
 670                 pinctrl-single,pins = <
 671                 OMAP4_IOPAD(0x0f6, PIN_INPUT | MUX_MODE0)       /* abe_mcbsp2_clkx */
 672                 OMAP4_IOPAD(0x0f8, PIN_INPUT | MUX_MODE0)       /* abe_mcbsp2_dr */
 673                 OMAP4_IOPAD(0x0fa, PIN_OUTPUT | MUX_MODE0)      /* abe_mcbsp2_dx */
 674                 OMAP4_IOPAD(0x0fc, PIN_INPUT | MUX_MODE0)       /* abe_mcbsp2_fsx */
 675                 >;
 676         };
 677
 678         mcbsp3_pins: pinmux_mcbsp3_pins {
 679                 pinctrl-single,pins = <
 680                 OMAP4_IOPAD(0x106, PIN_INPUT | MUX_MODE1)       /* abe_mcbsp3_dr */
 681                 OMAP4_IOPAD(0x108, PIN_OUTPUT | MUX_MODE1)      /* abe_mcbsp3_dx */
 682                 OMAP4_IOPAD(0x10a, PIN_INPUT | MUX_MODE1)       /* abe_mcbsp3_clkx */
 683                 OMAP4_IOPAD(0x10c, PIN_INPUT | MUX_MODE1)       /* abe_mcbsp3_fsx */
 684                 >;
 685         };
 686
 687         vibrator_direction_pin: pinmux_vibrator_direction_pin {
 688                 pinctrl-single,pins = <
 689                 OMAP4_IOPAD(0x1ce, PIN_OUTPUT | MUX_MODE1)      /* dmtimer8_pwm_evt (gpio_27) */
 690                 >;
 691         };
 692
 693         vibrator_enable_pin: pinmux_vibrator_enable_pin {
 694                 pinctrl-single,pins = <
 695                 OMAP4_IOPAD(0X1d0, PIN_OUTPUT | MUX_MODE1)      /* dmtimer9_pwm_evt (gpio_28) */
 696                 >;
 697         };
 698 };
 699
 700 &omap4_pmx_wkup {
 701         usb_gpio_mux_sel2: pinmux_usb_gpio_mux_sel2_pins {
 702                 /* gpio_wk0 */
 703                 pinctrl-single,pins = <
 704                 OMAP4_IOPAD(0x040, PIN_OUTPUT_PULLDOWN | MUX_MODE3)
 705                 >;
 706         };
 707 };
 708
 709 /* RNG is used by secure mode and not accessible */
 710 &rng_target {
 711         status = "disabled";
 712 };
 713
 714 /* Configure pwm clock source for timers 8 & 9 */
 715 &timer8 {
 716         assigned-clocks = <&abe_clkctrl OMAP4_TIMER8_CLKCTRL 24>;
 717         assigned-clock-parents = <&sys_clkin_ck>;
 718 };
 719
 720 &timer9 {
 721         assigned-clocks = <&l4_per_clkctrl OMAP4_TIMER9_CLKCTRL 24>;
 722         assigned-clock-parents = <&sys_clkin_ck>;
 723 };
 724
 725 /*
 726  * The uart1 port is wired to mdm6600 with rts and cts. The modem uses gpio_149
 727  * for wake-up events for both the USB PHY and the UART. We can use gpio_149
 728  * pad as the shared wakeirq for the UART rather than the RX or CTS pad as we
 729  * have gpio_149 trigger before the UART transfer starts.
 730  */
 731 &uart1 {
 732         pinctrl-names = "default";
 733         pinctrl-0 = <&uart1_pins>;
 734         interrupts-extended = <&wakeupgen GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH
 735                                &omap4_pmx_core 0x110>;
 736         uart-has-rtscts;
 737         current-speed = <115200>;
 738 };
 739
 740 &uart3 {
 741         interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH
 742                                &omap4_pmx_core 0x17c>;
 743 };
 744
 745 &uart4 {
 746         pinctrl-names = "default";
 747         pinctrl-0 = <&uart4_pins>;
 748
 749         bluetooth {
 750                 compatible = "ti,wl1285-st";
 751                 enable-gpios = <&gpio6 14 GPIO_ACTIVE_HIGH>; /* gpio 174 */
 752                 max-speed = <3686400>;
 753         };
 754 };
 755
 756 &usbhsohci {
 757         phys = <&fsusb1_phy>;
 758         phy-names = "usb";
 759 };
 760
 761 &usbhsehci {
 762         phys = <&hsusb2_phy>;
 763 };
 764
 765 &usbhshost {
 766         port1-mode = "ohci-phy-4pin-dpdm";
 767         port2-mode = "ehci-tll";
 768 };
 769
 770 /* Internal UTMI+ PHY used for OTG, CPCAP ULPI PHY for detection and charger */
 771 &usb_otg_hs {
 772         interface-type = <1>;
 773         mode = <3>;
 774
 775         /*
 776          * Max 300 mA steps based on similar PMIC MC13783UG.pdf "Table 10-4.
 777          * VBUS Regulator Main Characteristics". Binding uses 2 mA units.
 778          */
 779         power = <150>;
 780 };
 781
 782 &i2c4 {
 783         ak8975: magnetometer@c {
 784                 compatible = "asahi-kasei,ak8975";
 785                 reg = <0x0c>;
 786
 787                 vdd-supply = <&vhvio>;
 788
 789                 interrupt-parent = <&gpio6>;
 790                 interrupts = <15 IRQ_TYPE_EDGE_RISING>; /* gpio175 */
 791
 792                 rotation-matrix = "-1", "0", "0",
 793                                   "0", "1", "0",
 794                                   "0", "0", "-1";
 795
 796         };
 797
 798         lis3dh: accelerometer@18 {
 799                 compatible = "st,lis3dh-accel";
 800                 reg = <0x18>;
 801
 802                 vdd-supply = <&vhvio>;
 803
 804                 interrupt-parent = <&gpio2>;
 805                 interrupts = <2 IRQ_TYPE_EDGE_BOTH>; /* gpio34 */
 806
 807                 rotation-matrix = "0", "-1", "0",
 808                                   "1", "0", "0",
 809                                   "0", "0", "1";
 810         };
 811 };
 812
 813 &mcbsp2 {
 814         #sound-dai-cells = <0>;
 815         pinctrl-names = "default";
 816         pinctrl-0 = <&mcbsp2_pins>;
 817         status = "okay";
 818
 819         mcbsp2_port: port {
 820                 cpu_dai2: endpoint {
 821                         dai-format = "i2s";
 822                         remote-endpoint = <&cpcap_audio_codec0>;
 823                         frame-master = <&cpcap_audio_codec0>;
 824                         bitclock-master = <&cpcap_audio_codec0>;
 825                 };
 826         };
 827 };
 828
 829 &mcbsp3 {
 830         #sound-dai-cells = <0>;
 831         pinctrl-names = "default";
 832         pinctrl-0 = <&mcbsp3_pins>;
 833         status = "okay";
 834
 835         mcbsp3_port: port {
 836                 cpu_dai3: endpoint {
 837                         dai-format = "dsp_a";
 838                         frame-master = <&cpcap_audio_codec1>;
 839                         bitclock-master = <&cpcap_audio_codec1>;
 840                         remote-endpoint = <&cpcap_audio_codec1>;
 841                 };
 842         };
 843 };
 844
 845 &cpcap_audio_codec0 {
 846         remote-endpoint = <&cpu_dai2>;
 847 };
 848
 849 &cpcap_audio_codec1 {
 850         remote-endpoint = <&cpu_dai3>;
 851 };