arch/arm/boot/dts/motorola-mapphone-common.dtsi

   1 // SPDX-License-Identifier: GPL-2.0-only
   2 /dts-v1/;
   3
   4 #include <dt-bindings/input/input.h>
   5 #include "omap443x.dtsi"
   6 #include "motorola-cpcap-mapphone.dtsi"
   7
   8 / {
   9         chosen {
  10                 stdout-path = &uart3;
  11         };
  12
  13         aliases {
  14                 display0 = &lcd0;
  15                 display1 = &hdmi0;
  16         };
  17
  18         /*
  19          * We seem to have only 1021 MB accessible, 1021 - 1022 is locked,
  20          * then 1023 - 1024 seems to contain mbm.
  21          */
  22         memory {
  23                 device_type = "memory";
  24                 reg = <0x80000000 0x3fd00000>;  /* 1021 MB */
  25         };
  26
  27         /* Poweroff GPIO probably connected to CPCAP */
  28         gpio-poweroff {
  29                 compatible = "gpio-poweroff";
  30                 pinctrl-0 = <&poweroff_gpio>;
  31                 pinctrl-names = "default";
  32                 gpios = <&gpio2 18 GPIO_ACTIVE_LOW>;    /* gpio50 */
  33         };
  34
  35         hdmi0: connector {
  36                 compatible = "hdmi-connector";
  37                 pinctrl-0 = <&hdmi_hpd_gpio>;
  38                 pinctrl-names = "default";
  39                 label = "hdmi";
  40                 type = "d";
  41
  42                 hpd-gpios = <&gpio2 31 GPIO_ACTIVE_HIGH>;       /* gpio63 */
  43
  44                 port {
  45                         hdmi_connector_in: endpoint {
  46                                 remote-endpoint = <&hdmi_out>;
  47                         };
  48                 };
  49         };
  50
  51         /*
  52          * HDMI 5V regulator probably sourced from battery. Let's keep
  53          * keep this as always enabled for HDMI to work until we've
  54          * figured what the encoder chip is.
  55          */
  56         hdmi_regulator: regulator-hdmi {
  57                 compatible = "regulator-fixed";
  58                 regulator-name = "hdmi";
  59                 regulator-min-microvolt = <5000000>;
  60                 regulator-max-microvolt = <5000000>;
  61                 gpio = <&gpio2 27 GPIO_ACTIVE_HIGH>;    /* gpio59 */
  62                 enable-active-high;
  63                 regulator-always-on;
  64         };
  65
  66         /* FS USB Host PHY on port 1 for mdm6600 */
  67         fsusb1_phy: usb-phy@1 {
  68                 compatible = "motorola,mapphone-mdm6600";
  69                 pinctrl-0 = <&usb_mdm6600_pins>;
  70                 pinctrl-names = "default";
  71                 enable-gpios = <&gpio3 31 GPIO_ACTIVE_LOW>;     /* gpio_95 */
  72                 power-gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>;     /* gpio_54 */
  73                 reset-gpios = <&gpio2 17 GPIO_ACTIVE_HIGH>;     /* gpio_49 */
  74                 /* mode: gpio_148 gpio_149 */
  75                 motorola,mode-gpios = <&gpio5 20 GPIO_ACTIVE_HIGH>,
  76                                       <&gpio5 21 GPIO_ACTIVE_HIGH>;
  77                 /* cmd: gpio_103 gpio_104 gpio_142 */
  78                 motorola,cmd-gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>,
  79                                      <&gpio4 8 GPIO_ACTIVE_HIGH>,
  80                                      <&gpio5 14 GPIO_ACTIVE_HIGH>;
  81                 /* status: gpio_52 gpio_53 gpio_55 */
  82                 motorola,status-gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>,
  83                                         <&gpio2 21 GPIO_ACTIVE_HIGH>,
  84                                         <&gpio2 23 GPIO_ACTIVE_HIGH>;
  85                 #phy-cells = <0>;
  86         };
  87
  88         /* HS USB host TLL nop-phy on port 2 for w3glte */
  89         hsusb2_phy: usb-phy@2 {
  90                 compatible = "usb-nop-xceiv";
  91                 #phy-cells = <0>;
  92         };
  93
  94         /* LCD regulator from sw5 source */
  95         lcd_regulator: regulator-lcd {
  96                 compatible = "regulator-fixed";
  97                 regulator-name = "lcd";
  98                 regulator-min-microvolt = <5050000>;
  99                 regulator-max-microvolt = <5050000>;
 100                 gpio = <&gpio4 0 GPIO_ACTIVE_HIGH>;     /* gpio96 */
 101                 enable-active-high;
 102                 vin-supply = <&sw5>;
 103         };
 104
 105         /* This is probably coming straight from the battery.. */
 106         wl12xx_vmmc: regulator-wl12xx {
 107                 compatible = "regulator-fixed";
 108                 regulator-name = "vwl1271";
 109                 regulator-min-microvolt = <1650000>;
 110                 regulator-max-microvolt = <1650000>;
 111                 gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>;    /* gpio94 */
 112                 startup-delay-us = <70000>;
 113                 enable-active-high;
 114         };
 115
 116         soundcard {
 117                 compatible = "audio-graph-card";
 118                 label = "Mapphone Audio";
 119
 120                 widgets =
 121                         "Speaker", "Earpiece",
 122                         "Speaker", "Loudspeaker",
 123                         "Headphone", "Headphone Jack",
 124                         "Microphone", "Internal Mic";
 125
 126                 routing =
 127                         "Earpiece", "EP",
 128                         "Loudspeaker", "SPKR",
 129                         "Headphone Jack", "HSL",
 130                         "Headphone Jack", "HSR",
 131                         "MICR", "Internal Mic";
 132
 133                 dais = <&mcbsp2_port>, <&mcbsp3_port>;
 134         };
 135
 136         pwm8: dmtimer-pwm-8 {
 137                 pinctrl-names = "default";
 138                 pinctrl-0 = <&vibrator_direction_pin>;
 139
 140                 compatible = "ti,omap-dmtimer-pwm";
 141                 #pwm-cells = <3>;
 142                 ti,timers = <&timer8>;
 143                 ti,clock-source = <0x01>;
 144         };
 145
 146         pwm9: dmtimer-pwm-9 {
 147                 pinctrl-names = "default";
 148                 pinctrl-0 = <&vibrator_enable_pin>;
 149
 150                 compatible = "ti,omap-dmtimer-pwm";
 151                 #pwm-cells = <3>;
 152                 ti,timers = <&timer9>;
 153                 ti,clock-source = <0x01>;
 154         };
 155
 156         vibrator {
 157                 compatible = "pwm-vibrator";
 158                 pwms = <&pwm9 0 10000000 0>, <&pwm8 0 10000000 0>;
 159                 pwm-names = "enable", "direction";
 160                 direction-duty-cycle-ns = <10000000>;
 161         };
 162
 163         backlight: backlight {
 164                 compatible = "led-backlight";
 165
 166                 leds = <&backlight_led>;
 167                 brightness-levels = <31 63 95 127 159 191 223 255>;
 168                 default-brightness-level = <6>;
 169         };
 170 };
 171
 172 &cpu_thermal {
 173         polling-delay = <10000>; /* milliseconds */
 174 };
 175
 176 &cpu_alert0 {
 177         temperature = <80000>; /* millicelsius */
 178 };
 179
 180 &cpu0 {
 181         /*
 182          * Note that the 1.2GiHz mode is enabled for all SoC variants for
 183          * the Motorola Android Linux v3.0.8 based kernel.
 184          */
 185         operating-points = <
 186                 /* kHz    uV */
 187                 300000  1025000
 188                 600000  1200000
 189                 800000  1313000
 190                 1008000 1375000
 191                 1200000 1375000
 192         >;
 193 };
 194
 195 &dss {
 196         status = "okay";
 197 };
 198
 199 &dsi1 {
 200         status = "okay";
 201         vdd-supply = <&vcsi>;
 202
 203         port {
 204                 dsi1_out_ep: endpoint {
 205                         remote-endpoint = <&lcd0_in>;
 206                         lanes = <0 1 2 3 4 5>;
 207                 };
 208         };
 209
 210         lcd0: panel@0 {
 211                 compatible = "motorola,droid4-panel", "panel-dsi-cm";
 212                 reg = <0>;
 213                 label = "lcd0";
 214                 vddi-supply = <&lcd_regulator>;
 215                 reset-gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>;      /* gpio101 */
 216
 217                 backlight = <&backlight>;
 218
 219                 width-mm = <50>;
 220                 height-mm = <89>;
 221                 rotation = <90>;
 222
 223                 panel-timing {
 224                         clock-frequency = <0>;          /* Calculated by dsi */
 225
 226                         hback-porch = <2>;
 227                         hactive = <540>;
 228                         hfront-porch = <0>;
 229                         hsync-len = <2>;
 230
 231                         vback-porch = <1>;
 232                         vactive = <960>;
 233                         vfront-porch = <0>;
 234                         vsync-len = <1>;
 235
 236                         hsync-active = <0>;
 237                         vsync-active = <0>;
 238                         de-active = <1>;
 239                         pixelclk-active = <1>;
 240                 };
 241
 242                 port {
 243                         lcd0_in: endpoint {
 244                                 remote-endpoint = <&dsi1_out_ep>;
 245                         };
 246                 };
 247         };
 248 };
 249
 250 &hdmi {
 251         status = "okay";
 252         pinctrl-0 = <&dss_hdmi_pins>;
 253         pinctrl-names = "default";
 254         vdda-supply = <&vdac>;
 255
 256         port {
 257                 hdmi_out: endpoint {
 258                         remote-endpoint = <&hdmi_connector_in>;
 259                         lanes = <1 0 3 2 5 4 7 6>;
 260                 };
 261         };
 262 };
 263
 264 /* Battery NVRAM on 1-wire handled by w1_ds250x driver */
 265 &hdqw1w {
 266         pinctrl-0 = <&hdq_pins>;
 267         pinctrl-names = "default";
 268         ti,mode = "1w";
 269 };
 270
 271 &i2c1 {
 272         tmp105@48 {
 273                 compatible = "ti,tmp105";
 274                 reg = <0x48>;
 275                 pinctrl-0 = <&tmp105_irq>;
 276                 pinctrl-names = "default";
 277                 /* kpd_row0.gpio_178 */
 278                 interrupts-extended = <&gpio6 18 IRQ_TYPE_EDGE_FALLING
 279                                        &omap4_pmx_core 0x14e>;
 280                 interrupt-names = "irq", "wakeup";
 281                 wakeup-source;
 282         };
 283 };
 284
 285 &mmc1 {
 286         vmmc-supply = <&vwlan2>;
 287         bus-width = <4>;
 288         cd-gpios = <&gpio6 16 GPIO_ACTIVE_LOW>; /* gpio176 */
 289 };
 290
 291 &mmc2 {
 292         vmmc-supply = <&vsdio>;
 293         bus-width = <8>;
 294         ti,non-removable;
 295 };
 296
 297 &mmc3 {
 298         pinctrl-names = "default";
 299         pinctrl-0 = <&mmc3_pins>;
 300         vmmc-supply = <&wl12xx_vmmc>;
 301         /* uart2_tx.sdmmc3_dat1 pad as wakeirq */
 302         interrupts-extended = <&wakeupgen GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH
 303                                &omap4_pmx_core 0xde>;
 304         interrupt-names = "irq", "wakeup";
 305         non-removable;
 306         bus-width = <4>;
 307         cap-power-off-card;
 308         keep-power-in-suspend;
 309
 310         #address-cells = <1>;
 311         #size-cells = <0>;
 312         wlcore: wlcore@2 {
 313                 compatible = "ti,wl1285", "ti,wl1283";
 314                 reg = <2>;
 315                 /* gpio_100 with gpmc_wait2 pad as wakeirq */
 316                 interrupts-extended = <&gpio4 4 IRQ_TYPE_LEVEL_HIGH>,
 317                                       <&omap4_pmx_core 0x4e>;
 318                 interrupt-names = "irq", "wakeup";
 319                 ref-clock-frequency = <26000000>;
 320                 tcxo-clock-frequency = <26000000>;
 321         };
 322 };
 323
 324 &i2c2 {
 325         touchscreen@4a {
 326                 compatible = "atmel,maxtouch";
 327                 reg = <0x4a>;
 328                 pinctrl-names = "default";
 329                 pinctrl-0 = <&touchscreen_pins>;
 330
 331                 reset-gpios = <&gpio6 13 GPIO_ACTIVE_LOW>; /* gpio173 */
 332
 333                 /* gpio_183 with sys_nirq2 pad as wakeup */
 334                 interrupts-extended = <&gpio6 23 IRQ_TYPE_LEVEL_LOW>,
 335                                       <&omap4_pmx_core 0x160>;
 336                 interrupt-names = "irq", "wakeup";
 337                 wakeup-source;
 338         };
 339
 340         isl29030@44 {
 341                 compatible = "isil,isl29030";
 342                 reg = <0x44>;
 343
 344                 pinctrl-names = "default";
 345                 pinctrl-0 = <&als_proximity_pins>;
 346
 347                 interrupt-parent = <&gpio6>;
 348                 interrupts = <17 IRQ_TYPE_LEVEL_LOW>; /* gpio177 */
 349         };
 350 };
 351
 352 &omap4_pmx_core {
 353
 354         /* hdmi_hpd.gpio_63 */
 355         hdmi_hpd_gpio: pinmux_hdmi_hpd_pins {
 356                 pinctrl-single,pins = <
 357                 OMAP4_IOPAD(0x098, PIN_INPUT | MUX_MODE3)
 358                 >;
 359         };
 360
 361         hdq_pins: pinmux_hdq_pins {
 362                 pinctrl-single,pins = <
 363                 /* 0x4a100120 hdq_sio.hdq_sio aa27 */
 364                 OMAP4_IOPAD(0x120, PIN_INPUT | MUX_MODE0)
 365                 >;
 366         };
 367
 368         /* hdmi_cec.hdmi_cec, hdmi_scl.hdmi_scl, hdmi_sda.hdmi_sda */
 369         dss_hdmi_pins: pinmux_dss_hdmi_pins {
 370                 pinctrl-single,pins = <
 371                 OMAP4_IOPAD(0x09a, PIN_INPUT | MUX_MODE0)
 372                 OMAP4_IOPAD(0x09c, PIN_INPUT | MUX_MODE0)
 373                 OMAP4_IOPAD(0x09e, PIN_INPUT | MUX_MODE0)
 374                 >;
 375         };
 376
 377         /*
 378          * Android uses PIN_OFF_INPUT_PULLDOWN | PIN_INPUT_PULLUP | MUX_MODE3
 379          * for gpio_100, but the internal pull makes wlan flakey on some
 380          * devices. Off mode value should be tested if we have off mode working
 381          * later on.
 382          */
 383         mmc3_pins: pinmux_mmc3_pins {
 384                 pinctrl-single,pins = <
 385                 /* 0x4a10008e gpmc_wait2.gpio_100 d23 */
 386                 OMAP4_IOPAD(0x08e, PIN_INPUT | MUX_MODE3)
 387
 388                 /* 0x4a100102 abe_mcbsp1_dx.sdmmc3_dat2 ab25 */
 389                 OMAP4_IOPAD(0x102, PIN_INPUT_PULLUP | MUX_MODE1)
 390
 391                 /* 0x4a100104 abe_mcbsp1_fsx.sdmmc3_dat3 ac27 */
 392                 OMAP4_IOPAD(0x104, PIN_INPUT_PULLUP | MUX_MODE1)
 393
 394                 /* 0x4a100118 uart2_cts.sdmmc3_clk ab26 */
 395                 OMAP4_IOPAD(0x118, PIN_INPUT | MUX_MODE1)
 396
 397                 /* 0x4a10011a uart2_rts.sdmmc3_cmd ab27 */
 398                 OMAP4_IOPAD(0x11a, PIN_INPUT_PULLUP | MUX_MODE1)
 399
 400                 /* 0x4a10011c uart2_rx.sdmmc3_dat0 aa25 */
 401                 OMAP4_IOPAD(0x11c, PIN_INPUT_PULLUP | MUX_MODE1)
 402
 403                 /* 0x4a10011e uart2_tx.sdmmc3_dat1 aa26 */
 404                 OMAP4_IOPAD(0x11e, PIN_INPUT_PULLUP | MUX_MODE1)
 405                 >;
 406         };
 407
 408         /* gpmc_ncs0.gpio_50 */
 409         poweroff_gpio: pinmux_poweroff_pins {
 410                 pinctrl-single,pins = <
 411                 OMAP4_IOPAD(0x074, PIN_OUTPUT_PULLUP | MUX_MODE3)
 412                 >;
 413         };
 414
 415         /* kpd_row0.gpio_178 */
 416         tmp105_irq: pinmux_tmp105_irq {
 417                 pinctrl-single,pins = <
 418                 OMAP4_IOPAD(0x18e, PIN_INPUT_PULLUP | MUX_MODE3)
 419                 >;
 420         };
 421
 422         usb_gpio_mux_sel1: pinmux_usb_gpio_mux_sel1_pins {
 423                 /* gpio_60 */
 424                 pinctrl-single,pins = <
 425                 OMAP4_IOPAD(0x088, PIN_OUTPUT | MUX_MODE3)
 426                 >;
 427         };
 428
 429         touchscreen_pins: pinmux_touchscreen_pins {
 430                 pinctrl-single,pins = <
 431                 OMAP4_IOPAD(0x180, PIN_OUTPUT | MUX_MODE3)
 432                 OMAP4_IOPAD(0x1a0, PIN_INPUT_PULLUP | MUX_MODE3)
 433                 >;
 434         };
 435
 436         als_proximity_pins: pinmux_als_proximity_pins {
 437                 pinctrl-single,pins = <
 438                 OMAP4_IOPAD(0x18c, PIN_INPUT_PULLUP | MUX_MODE3)
 439                 >;
 440         };
 441
 442         usb_mdm6600_pins: pinmux_usb_mdm6600_pins {
 443                 pinctrl-single,pins = <
 444                 /* enable 0x4a1000d8 usbb1_ulpitll_dat7.gpio_95 ag16 */
 445                 OMAP4_IOPAD(0x0d8, PIN_INPUT | MUX_MODE3)
 446
 447                 /* power 0x4a10007c gpmc_nwp.gpio_54 c25 */
 448                 OMAP4_IOPAD(0x07c, PIN_OUTPUT | MUX_MODE3)
 449
 450                 /* reset 0x4a100072 gpmc_a25.gpio_49 d20 */
 451                 OMAP4_IOPAD(0x072, PIN_OUTPUT | MUX_MODE3)
 452
 453                 /* mode0/bpwake 0x4a10014e sdmmc5_dat1.gpio_148 af4 */
 454                 OMAP4_IOPAD(0x14e, PIN_OUTPUT | MUX_MODE3)
 455
 456                 /* mode1/apwake 0x4a100150 sdmmc5_dat2.gpio_149 ag3 */
 457                 OMAP4_IOPAD(0x150, PIN_OFF_OUTPUT_LOW | PIN_INPUT | MUX_MODE3)
 458
 459                 /* status0 0x4a10007e gpmc_clk.gpio_55 b22 */
 460                 OMAP4_IOPAD(0x07e, PIN_INPUT | MUX_MODE3)
 461
 462                 /* status1 0x4a10007a gpmc_ncs3.gpio_53 c22 */
 463                 OMAP4_IOPAD(0x07a, PIN_INPUT | MUX_MODE3)
 464
 465                 /* status2 0x4a100078 gpmc_ncs2.gpio_52 d21 */
 466                 OMAP4_IOPAD(0x078, PIN_INPUT | MUX_MODE3)
 467
 468                 /* cmd0 0x4a100094 gpmc_ncs6.gpio_103 c24 */
 469                 OMAP4_IOPAD(0x094, PIN_OUTPUT | MUX_MODE3)
 470
 471                 /* cmd1 0x4a100096 gpmc_ncs7.gpio_104 d24 */
 472                 OMAP4_IOPAD(0x096, PIN_OUTPUT | MUX_MODE3)
 473
 474                 /* cmd2 0x4a100142 uart3_rts_sd.gpio_142 f28 */
 475                 OMAP4_IOPAD(0x142, PIN_OUTPUT | MUX_MODE3)
 476                 >;
 477         };
 478
 479         usb_ulpi_pins: pinmux_usb_ulpi_pins {
 480                 pinctrl-single,pins = <
 481                 OMAP4_IOPAD(0x196, MUX_MODE7)
 482                 OMAP4_IOPAD(0x198, MUX_MODE7)
 483                 OMAP4_IOPAD(0x1b2, PIN_INPUT_PULLUP | MUX_MODE0)
 484                 OMAP4_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE0)
 485                 OMAP4_IOPAD(0x1b6, PIN_INPUT_PULLUP | MUX_MODE0)
 486                 OMAP4_IOPAD(0x1b8, PIN_INPUT_PULLUP | MUX_MODE0)
 487                 OMAP4_IOPAD(0x1ba, PIN_INPUT_PULLUP | MUX_MODE0)
 488                 OMAP4_IOPAD(0x1bc, PIN_INPUT_PULLUP | MUX_MODE0)
 489                 OMAP4_IOPAD(0x1be, PIN_INPUT_PULLUP | MUX_MODE0)
 490                 OMAP4_IOPAD(0x1c0, PIN_INPUT_PULLUP | MUX_MODE0)
 491                 OMAP4_IOPAD(0x1c2, PIN_INPUT_PULLUP | MUX_MODE0)
 492                 OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE0)
 493                 OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE0)
 494                 OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE0)
 495                 >;
 496         };
 497
 498         /* usb0_otg_dp and usb0_otg_dm */
 499         usb_utmi_pins: pinmux_usb_utmi_pins {
 500                 pinctrl-single,pins = <
 501                 OMAP4_IOPAD(0x196, PIN_INPUT | MUX_MODE0)
 502                 OMAP4_IOPAD(0x198, PIN_INPUT | MUX_MODE0)
 503                 OMAP4_IOPAD(0x1b2, PIN_INPUT_PULLUP | MUX_MODE7)
 504                 OMAP4_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE7)
 505                 OMAP4_IOPAD(0x1b6, PIN_INPUT_PULLUP | MUX_MODE7)
 506                 OMAP4_IOPAD(0x1b8, PIN_INPUT_PULLUP | MUX_MODE7)
 507                 OMAP4_IOPAD(0x1ba, PIN_INPUT_PULLUP | MUX_MODE7)
 508                 OMAP4_IOPAD(0x1bc, PIN_INPUT_PULLUP | MUX_MODE7)
 509                 OMAP4_IOPAD(0x1be, PIN_INPUT_PULLUP | MUX_MODE7)
 510                 OMAP4_IOPAD(0x1c0, PIN_INPUT_PULLUP | MUX_MODE7)
 511                 OMAP4_IOPAD(0x1c2, PIN_INPUT_PULLUP | MUX_MODE7)
 512                 OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE7)
 513                 OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE7)
 514                 OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE7)
 515                 >;
 516         };
 517
 518         /*
 519          * Note that the v3.0.8 stock userspace dynamically remuxes uart1
 520          * rts pin probably for PM purposes to PIN_INPUT_PULLUP | MUX_MODE7
 521          * when not used. If needed, we can add rts pin remux later based
 522          * on power measurements.
 523          */
 524         uart1_pins: pinmux_uart1_pins {
 525                 pinctrl-single,pins = <
 526                 /* 0x4a10013c mcspi1_cs2.uart1_cts ag23 */
 527                 OMAP4_IOPAD(0x13c, PIN_INPUT_PULLUP | MUX_MODE1)
 528
 529                 /* 0x4a10013e mcspi1_cs3.uart1_rts ah23 */
 530                 OMAP4_IOPAD(0x13e, MUX_MODE1)
 531
 532                 /* 0x4a100140 uart3_cts_rctx.uart1_tx f27 */
 533                 OMAP4_IOPAD(0x140, PIN_OUTPUT | MUX_MODE1)
 534
 535                 /* 0x4a1001ca dpm_emu14.uart1_rx aa3 */
 536                 OMAP4_IOPAD(0x1ca, PIN_INPUT_PULLUP | MUX_MODE2)
 537                 >;
 538         };
 539
 540         /* uart3_tx_irtx and uart3_rx_irrx */
 541         uart3_pins: pinmux_uart3_pins {
 542                 pinctrl-single,pins = <
 543                 OMAP4_IOPAD(0x196, MUX_MODE7)
 544                 OMAP4_IOPAD(0x198, MUX_MODE7)
 545                 OMAP4_IOPAD(0x1b2, PIN_INPUT_PULLUP | MUX_MODE7)
 546                 OMAP4_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE7)
 547                 OMAP4_IOPAD(0x1b6, PIN_INPUT_PULLUP | MUX_MODE7)
 548                 OMAP4_IOPAD(0x1b8, PIN_INPUT_PULLUP | MUX_MODE7)
 549                 OMAP4_IOPAD(0x1ba, MUX_MODE2)
 550                 OMAP4_IOPAD(0x1bc, PIN_INPUT | MUX_MODE2)
 551                 OMAP4_IOPAD(0x1be, PIN_INPUT_PULLUP | MUX_MODE7)
 552                 OMAP4_IOPAD(0x1c0, PIN_INPUT_PULLUP | MUX_MODE7)
 553                 OMAP4_IOPAD(0x1c2, PIN_INPUT_PULLUP | MUX_MODE7)
 554                 OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE7)
 555                 OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE7)
 556                 OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE7)
 557                 >;
 558         };
 559
 560         uart4_pins: pinmux_uart4_pins {
 561                 pinctrl-single,pins = <
 562                 OMAP4_IOPAD(0x15c, PIN_INPUT | MUX_MODE0)               /* uart4_rx */
 563                 OMAP4_IOPAD(0x15e, PIN_OUTPUT | MUX_MODE0)              /* uart4_tx */
 564                 OMAP4_IOPAD(0x110, PIN_INPUT_PULLUP | MUX_MODE5)        /* uart4_cts */
 565                 OMAP4_IOPAD(0x112, PIN_OUTPUT_PULLUP | MUX_MODE5)       /* uart4_rts */
 566                 >;
 567         };
 568
 569         mcbsp2_pins: pinmux_mcbsp2_pins {
 570                 pinctrl-single,pins = <
 571                 OMAP4_IOPAD(0x0f6, PIN_INPUT | MUX_MODE0)       /* abe_mcbsp2_clkx */
 572                 OMAP4_IOPAD(0x0f8, PIN_INPUT | MUX_MODE0)       /* abe_mcbsp2_dr */
 573                 OMAP4_IOPAD(0x0fa, PIN_OUTPUT | MUX_MODE0)      /* abe_mcbsp2_dx */
 574                 OMAP4_IOPAD(0x0fc, PIN_INPUT | MUX_MODE0)       /* abe_mcbsp2_fsx */
 575                 >;
 576         };
 577
 578         mcbsp3_pins: pinmux_mcbsp3_pins {
 579                 pinctrl-single,pins = <
 580                 OMAP4_IOPAD(0x106, PIN_INPUT | MUX_MODE1)       /* abe_mcbsp3_dr */
 581                 OMAP4_IOPAD(0x108, PIN_OUTPUT | MUX_MODE1)      /* abe_mcbsp3_dx */
 582                 OMAP4_IOPAD(0x10a, PIN_INPUT | MUX_MODE1)       /* abe_mcbsp3_clkx */
 583                 OMAP4_IOPAD(0x10c, PIN_INPUT | MUX_MODE1)       /* abe_mcbsp3_fsx */
 584                 >;
 585         };
 586
 587         vibrator_direction_pin: pinmux_vibrator_direction_pin {
 588                 pinctrl-single,pins = <
 589                 OMAP4_IOPAD(0x1ce, PIN_OUTPUT | MUX_MODE1)      /* dmtimer8_pwm_evt (gpio_27) */
 590                 >;
 591         };
 592
 593         vibrator_enable_pin: pinmux_vibrator_enable_pin {
 594                 pinctrl-single,pins = <
 595                 OMAP4_IOPAD(0X1d0, PIN_OUTPUT | MUX_MODE1)      /* dmtimer9_pwm_evt (gpio_28) */
 596                 >;
 597         };
 598 };
 599
 600 &omap4_pmx_wkup {
 601         usb_gpio_mux_sel2: pinmux_usb_gpio_mux_sel2_pins {
 602                 /* gpio_wk0 */
 603                 pinctrl-single,pins = <
 604                 OMAP4_IOPAD(0x040, PIN_OUTPUT_PULLDOWN | MUX_MODE3)
 605                 >;
 606         };
 607 };
 608
 609 /* RNG is used by secure mode and not accessible */
 610 &rng_target {
 611         status = "disabled";
 612 };
 613
 614 /* Configure pwm clock source for timers 8 & 9 */
 615 &timer8 {
 616         assigned-clocks = <&abe_clkctrl OMAP4_TIMER8_CLKCTRL 24>;
 617         assigned-clock-parents = <&sys_clkin_ck>;
 618 };
 619
 620 &timer9 {
 621         assigned-clocks = <&l4_per_clkctrl OMAP4_TIMER9_CLKCTRL 24>;
 622         assigned-clock-parents = <&sys_clkin_ck>;
 623 };
 624
 625 /*
 626  * The uart1 port is wired to mdm6600 with rts and cts. The modem uses gpio_149
 627  * for wake-up events for both the USB PHY and the UART. We can use gpio_149
 628  * pad as the shared wakeirq for the UART rather than the RX or CTS pad as we
 629  * have gpio_149 trigger before the UART transfer starts.
 630  */
 631 &uart1 {
 632         pinctrl-names = "default";
 633         pinctrl-0 = <&uart1_pins>;
 634         interrupts-extended = <&wakeupgen GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH
 635                                &omap4_pmx_core 0x110>;
 636         uart-has-rtscts;
 637         current-speed = <115200>;
 638 };
 639
 640 &uart3 {
 641         interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH
 642                                &omap4_pmx_core 0x17c>;
 643 };
 644
 645 &uart4 {
 646         pinctrl-names = "default";
 647         pinctrl-0 = <&uart4_pins>;
 648
 649         bluetooth {
 650                 compatible = "ti,wl1285-st";
 651                 enable-gpios = <&gpio6 14 GPIO_ACTIVE_HIGH>; /* gpio 174 */
 652                 max-speed = <3686400>;
 653         };
 654 };
 655
 656 &usbhsohci {
 657         phys = <&fsusb1_phy>;
 658         phy-names = "usb";
 659 };
 660
 661 &usbhsehci {
 662         phys = <&hsusb2_phy>;
 663 };
 664
 665 &usbhshost {
 666         port1-mode = "ohci-phy-4pin-dpdm";
 667         port2-mode = "ehci-tll";
 668 };
 669
 670 /* Internal UTMI+ PHY used for OTG, CPCAP ULPI PHY for detection and charger */
 671 &usb_otg_hs {
 672         interface-type = <1>;
 673         mode = <3>;
 674
 675         /*
 676          * Max 300 mA steps based on similar PMIC MC13783UG.pdf "Table 10-4.
 677          * VBUS Regulator Main Characteristics". Binding uses 2 mA units.
 678          */
 679         power = <150>;
 680 };
 681
 682 &i2c4 {
 683         ak8975: magnetometer@c {
 684                 compatible = "asahi-kasei,ak8975";
 685                 reg = <0x0c>;
 686
 687                 vdd-supply = <&vhvio>;
 688
 689                 interrupt-parent = <&gpio6>;
 690                 interrupts = <15 IRQ_TYPE_EDGE_RISING>; /* gpio175 */
 691
 692                 rotation-matrix = "-1", "0", "0",
 693                                   "0", "1", "0",
 694                                   "0", "0", "-1";
 695
 696         };
 697 };
 698
 699 &mcbsp2 {
 700         #sound-dai-cells = <0>;
 701         pinctrl-names = "default";
 702         pinctrl-0 = <&mcbsp2_pins>;
 703         status = "okay";
 704
 705         mcbsp2_port: port {
 706                 cpu_dai2: endpoint {
 707                         dai-format = "i2s";
 708                         remote-endpoint = <&cpcap_audio_codec0>;
 709                         frame-master = <&cpcap_audio_codec0>;
 710                         bitclock-master = <&cpcap_audio_codec0>;
 711                 };
 712         };
 713 };
 714
 715 &mcbsp3 {
 716         #sound-dai-cells = <0>;
 717         pinctrl-names = "default";
 718         pinctrl-0 = <&mcbsp3_pins>;
 719         status = "okay";
 720
 721         mcbsp3_port: port {
 722                 cpu_dai3: endpoint {
 723                         dai-format = "dsp_a";
 724                         frame-master = <&cpcap_audio_codec1>;
 725                         bitclock-master = <&cpcap_audio_codec1>;
 726                         remote-endpoint = <&cpcap_audio_codec1>;
 727                 };
 728         };
 729 };
 730
 731 &cpcap_audio_codec0 {
 732         remote-endpoint = <&cpu_dai2>;
 733 };
 734
 735 &cpcap_audio_codec1 {
 736         remote-endpoint = <&cpu_dai3>;
 737 };