arch/arm/boot/dts/logicpd-som-lv.dtsi

   1 /*
   2  * This program is free software; you can redistribute it and/or modify
   3  * it under the terms of the GNU General Public License version 2 as
   4  * published by the Free Software Foundation.
   5  */
   6
   7 #include <dt-bindings/input/input.h>
   8
   9 / {
  10         cpus {
  11                 cpu@0 {
  12                         cpu0-supply = <&vcc>;
  13                 };
  14         };
  15
  16         memory@80000000 {
  17                 device_type = "memory";
  18                 reg = <0x80000000 0>;
  19         };
  20
  21         wl12xx_vmmc: wl12xx_vmmc {
  22                 compatible = "regulator-fixed";
  23                 regulator-name = "vwl1271";
  24                 regulator-min-microvolt = <1800000>;
  25                 regulator-max-microvolt = <1800000>;
  26                 gpio = <&gpio1 3 0>;   /* gpio_3 */
  27                 startup-delay-us = <70000>;
  28                 enable-active-high;
  29                 vin-supply = <&vmmc2>;
  30         };
  31
  32         /* HS USB Host PHY on PORT 1 */
  33         hsusb2_phy: hsusb2_phy {
  34                 compatible = "usb-nop-xceiv";
  35                 reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; /* gpio_4 */
  36                 #phy-cells = <0>;
  37         };
  38 };
  39
  40 &gpmc {
  41         ranges = <0 0 0x30000000 0x1000000>;    /* CS0: 16MB for NAND */
  42
  43         nand@0,0 {
  44                 compatible = "ti,omap2-nand";
  45                 reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
  46                 interrupt-parent = <&gpmc>;
  47                 interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
  48                              <1 IRQ_TYPE_NONE>; /* termcount */
  49                 linux,mtd-name = "micron,mt29f4g16abbda3w";
  50                 nand-bus-width = <16>;
  51                 ti,nand-ecc-opt = "bch8";
  52                 rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */
  53                 gpmc,sync-clk-ps = <0>;
  54                 gpmc,cs-on-ns = <0>;
  55                 gpmc,cs-rd-off-ns = <44>;
  56                 gpmc,cs-wr-off-ns = <44>;
  57                 gpmc,adv-on-ns = <6>;
  58                 gpmc,adv-rd-off-ns = <34>;
  59                 gpmc,adv-wr-off-ns = <44>;
  60                 gpmc,we-off-ns = <40>;
  61                 gpmc,oe-off-ns = <54>;
  62                 gpmc,access-ns = <64>;
  63                 gpmc,rd-cycle-ns = <82>;
  64                 gpmc,wr-cycle-ns = <82>;
  65                 gpmc,wr-access-ns = <40>;
  66                 gpmc,wr-data-mux-bus-ns = <0>;
  67                 gpmc,device-width = <2>;
  68                 #address-cells = <1>;
  69                 #size-cells = <1>;
  70         };
  71 };
  72
  73 &i2c1 {
  74         pinctrl-names = "default";
  75         pinctrl-0 = <&i2c1_pins>;
  76         clock-frequency = <2600000>;
  77
  78         twl: twl@48 {
  79                 reg = <0x48>;
  80                 interrupts = <7>; /* SYS_NIRQ cascaded to intc */
  81                 interrupt-parent = <&intc>;
  82                 twl_audio: audio {
  83                         compatible = "ti,twl4030-audio";
  84                         codec {
  85                         };
  86                 };
  87         };
  88 };
  89
  90 &i2c2 {
  91         pinctrl-names = "default";
  92         pinctrl-0 = <&i2c2_pins>;
  93         clock-frequency = <400000>;
  94 };
  95
  96 &i2c3 {
  97         pinctrl-names = "default";
  98         pinctrl-0 = <&i2c3_pins>;
  99         clock-frequency = <400000>;
 100 };
 101
 102 &mmc3 {
 103         interrupts-extended = <&intc 94 &omap3_pmx_core2 0x46>;
 104         pinctrl-0 = <&mmc3_pins &wl127x_gpio>;
 105         pinctrl-names = "default";
 106         vmmc-supply = <&wl12xx_vmmc>;
 107         non-removable;
 108         bus-width = <4>;
 109         cap-power-off-card;
 110         #address-cells = <1>;
 111         #size-cells = <0>;
 112         wlcore: wlcore@2 {
 113                 compatible = "ti,wl1273";
 114                 reg = <2>;
 115                 interrupt-parent = <&gpio1>;
 116                 interrupts = <2 IRQ_TYPE_LEVEL_HIGH>; /* gpio 2 */
 117                 ref-clock-frequency = <26000000>;
 118         };
 119 };
 120
 121 &usbhshost {
 122         port2-mode = "ehci-phy";
 123 };
 124
 125 &usbhsehci {
 126         phys = <0 &hsusb2_phy>;
 127 };
 128
 129
 130 &omap3_pmx_core {
 131         pinctrl-names = "default";
 132         pinctrl-0 = <&hsusb2_pins>;
 133
 134         mmc3_pins: pinmux_mm3_pins {
 135                 pinctrl-single,pins = <
 136                         OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat4.sdmmc3_dat0 */
 137                         OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat5.sdmmc3_dat1 */
 138                         OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat2 */
 139                         OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat3 */
 140                         OMAP3_CORE1_IOPAD(0x21d0, PIN_INPUT_PULLUP | MUX_MODE3) /* mcspi1_cs1.sdmmc3_cmd */
 141                         OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT_PULLUP | MUX_MODE3) /* mcspi1_cs2.sdmmc_clk */
 142                 >;
 143         };
 144         mcbsp2_pins: pinmux_mcbsp2_pins {
 145                 pinctrl-single,pins = <
 146                         OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0)        /* mcbsp2_fsx */
 147                         OMAP3_CORE1_IOPAD(0x213e, PIN_INPUT | MUX_MODE0)        /* mcbsp2_clkx */
 148                         OMAP3_CORE1_IOPAD(0x2140, PIN_INPUT | MUX_MODE0)        /* mcbsp2_dr */
 149                         OMAP3_CORE1_IOPAD(0x2142, PIN_OUTPUT | MUX_MODE0)       /* mcbsp2_dx */
 150                 >;
 151         };
 152         uart2_pins: pinmux_uart2_pins {
 153                 pinctrl-single,pins = <
 154                         OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT | MUX_MODE0)        /* uart2_cts.uart2_cts */
 155                         OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0)       /* uart2_rts .uart2_rts*/
 156                         OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0)       /* uart2_tx.uart2_tx */
 157                         OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0)        /* uart2_rx.uart2_rx */
 158                         OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4)       /* GPIO_162,BT_EN */
 159                 >;
 160         };
 161         mcspi1_pins: pinmux_mcspi1_pins {
 162                 pinctrl-single,pins = <
 163                         OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0)        /* mcspi1_clk.mcspi1_clk */
 164                         OMAP3_CORE1_IOPAD(0x21ca, PIN_OUTPUT | MUX_MODE0)       /* mcspi1_simo.mcspi1_simo */
 165                         OMAP3_CORE1_IOPAD(0x21cc, PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi1_somi.mcspi1_somi */
 166                         OMAP3_CORE1_IOPAD(0x21ce, PIN_OUTPUT | MUX_MODE0)       /* mcspi1_cs0.mcspi1_cs0 */
 167                 >;
 168         };
 169
 170         hsusb2_pins: pinmux_hsusb2_pins {
 171                 pinctrl-single,pins = <
 172                         OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3)       /* mcspi1_cs3.hsusb2_data2 */
 173                         OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3)       /* mcspi2_clk.hsusb2_data7 */
 174                         OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3)       /* mcspi2_simo.hsusb2_data4 */
 175                         OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3)       /* mcspi2_somi.hsusb2_data5 */
 176                         OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3)       /* mcspi2_cs0.hsusb2_data6 */
 177                         OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3)       /* mcspi2_cs1.hsusb2_data3 */
 178                 >;
 179         };
 180
 181         hsusb_otg_pins: pinmux_hsusb_otg_pins {
 182                 pinctrl-single,pins = <
 183                         OMAP3_CORE1_IOPAD(0x21a2, PIN_INPUT | MUX_MODE0)        /* hsusb0_clk.hsusb0_clk */
 184                         OMAP3_CORE1_IOPAD(0x21a4, PIN_OUTPUT | MUX_MODE0)       /* hsusb0_stp.hsusb0_stp */
 185                         OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT | MUX_MODE0)        /* hsusb0_dir.hsusb0_dir */
 186                         OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT | MUX_MODE0)        /* hsusb0_nxt.hsusb0_nxt */
 187                         OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT | MUX_MODE0)        /* hsusb0_data0.hsusb0_data0 */
 188                         OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT | MUX_MODE0)        /* hsusb0_data1.hsusb0_data1 */
 189                         OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT | MUX_MODE0)        /* hsusb0_data2.hsusb0_data2 */
 190                         OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT | MUX_MODE0)        /* hsusb0_data3.hsusb0_data3 */
 191                         OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT | MUX_MODE0)        /* hsusb0_data4.hsusb0_data4 */
 192                         OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT | MUX_MODE0)        /* hsusb0_data5.hsusb0_data5 */
 193                         OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT | MUX_MODE0)        /* hsusb0_data6.hsusb0_data6 */
 194                         OMAP3_CORE1_IOPAD(0x21b8, PIN_INPUT | MUX_MODE0)        /* hsusb0_data7.hsusb0_data7 */
 195                 >;
 196         };
 197
 198         i2c1_pins: pinmux_i2c1_pins {
 199                 pinctrl-single,pins = <
 200                         OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT | MUX_MODE0)        /* i2c1_scl.i2c1_scl */
 201                         OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT | MUX_MODE0)        /* i2c1_sda.i2c1_sda */
 202                 >;
 203         };
 204 };
 205
 206 &omap3_pmx_wkup {
 207         pinctrl-names = "default";
 208         pinctrl-0 = <&hsusb2_reset_pin>;
 209         hsusb2_reset_pin: pinmux_hsusb1_reset_pin {
 210                 pinctrl-single,pins = <
 211                         OMAP3_WKUP_IOPAD(0x2a0e, PIN_OUTPUT | MUX_MODE4)        /* sys_boot2.gpio_4 */
 212                 >;
 213         };
 214         wl127x_gpio: pinmux_wl127x_gpio_pin {
 215                 pinctrl-single,pins = <
 216                         OMAP3_WKUP_IOPAD(0x2a0c, PIN_INPUT | MUX_MODE4)         /* sys_boot0.gpio_2 */
 217                         OMAP3_WKUP_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE4)        /* sys_boot1.gpio_3 */
 218                 >;
 219         };
 220         i2c2_pins: pinmux_i2c2_pins {
 221                 pinctrl-single,pins = <
 222                         OMAP3_CORE1_IOPAD(0x21be, PIN_INPUT | MUX_MODE0)        /* i2c2_scl */
 223                         OMAP3_CORE1_IOPAD(0x21c0, PIN_INPUT | MUX_MODE0)        /* i2c2_sda */
 224                 >;
 225         };
 226         i2c3_pins: pinmux_i2c3_pins {
 227                 pinctrl-single,pins = <
 228                         OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT | MUX_MODE0)        /* i2c3_scl */
 229                         OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT | MUX_MODE0)        /* i2c3_sda */
 230                 >;
 231         };
 232 };
 233
 234 &omap3_pmx_core2 {
 235         pinctrl-names = "default";
 236         pinctrl-0 = <&hsusb2_2_pins>;
 237         hsusb2_2_pins: pinmux_hsusb2_2_pins {
 238                 pinctrl-single,pins = <
 239                         OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)            /* etk_d10.hsusb2_clk */
 240                         OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)            /* etk_d11.hsusb2_stp */
 241                         OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d12.hsusb2_dir */
 242                         OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d13.hsusb2_nxt */
 243                         OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d14.hsusb2_data0 */
 244                         OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d15.hsusb2_data1 */
 245                 >;
 246         };
 247 };
 248
 249 &uart2 {
 250         interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>;
 251         pinctrl-names = "default";
 252         pinctrl-0 = <&uart2_pins>;
 253 };
 254
 255 &mcspi1 {
 256         pinctrl-names = "default";
 257         pinctrl-0 = <&mcspi1_pins>;
 258 };
 259
 260 #include "twl4030.dtsi"
 261 #include "twl4030_omap3.dtsi"
 262
 263 &twl {
 264         twl_power: power {
 265                 compatible = "ti,twl4030-power-idle-osc-off", "ti,twl4030-power-idle";
 266                 ti,use_poweroff;
 267         };
 268 };
 269
 270 &twl_gpio {
 271         ti,use-leds;
 272 };