1 # SPDX-License-Identifier: GPL-2.0
5 select ARCH_CLOCKSOURCE_DATA
6 select ARCH_DISCARD_MEMBLOCK if !HAVE_ARCH_PFN_VALID && !KEXEC
7 select ARCH_HAS_DEBUG_VIRTUAL if MMU
8 select ARCH_HAS_DEVMEM_IS_ALLOWED
9 select ARCH_HAS_ELF_RANDOMIZE
10 select ARCH_HAS_FORTIFY_SOURCE
11 select ARCH_HAS_SET_MEMORY
12 select ARCH_HAS_PHYS_TO_DMA
13 select ARCH_HAS_STRICT_KERNEL_RWX if MMU && !XIP_KERNEL
14 select ARCH_HAS_STRICT_MODULE_RWX if MMU
15 select ARCH_HAS_TICK_BROADCAST if GENERIC_CLOCKEVENTS_BROADCAST
16 select ARCH_HAVE_CUSTOM_GPIO_H
17 select ARCH_HAS_GCOV_PROFILE_ALL
18 select ARCH_MIGHT_HAVE_PC_PARPORT
19 select ARCH_OPTIONAL_KERNEL_RWX if ARCH_HAS_STRICT_KERNEL_RWX
20 select ARCH_OPTIONAL_KERNEL_RWX_DEFAULT if CPU_V7
21 select ARCH_SUPPORTS_ATOMIC_RMW
22 select ARCH_USE_BUILTIN_BSWAP
23 select ARCH_USE_CMPXCHG_LOCKREF
24 select ARCH_WANT_IPC_PARSE_VERSION
25 select BUILDTIME_EXTABLE_SORT if MMU
26 select CLONE_BACKWARDS
27 select CPU_PM if (SUSPEND || CPU_IDLE)
28 select DCACHE_WORD_ACCESS if HAVE_EFFICIENT_UNALIGNED_ACCESS
29 select DMA_DIRECT_OPS if !MMU
31 select EDAC_ATOMIC_SCRUB
32 select GENERIC_ALLOCATOR
33 select GENERIC_ARCH_TOPOLOGY if ARM_CPU_TOPOLOGY
34 select GENERIC_ATOMIC64 if (CPU_V7M || CPU_V6 || !CPU_32v6K || !AEABI)
35 select GENERIC_CLOCKEVENTS_BROADCAST if SMP
36 select GENERIC_CPU_AUTOPROBE
37 select GENERIC_EARLY_IOREMAP
38 select GENERIC_IDLE_POLL_SETUP
39 select GENERIC_IRQ_PROBE
40 select GENERIC_IRQ_SHOW
41 select GENERIC_IRQ_SHOW_LEVEL
42 select GENERIC_PCI_IOMAP
43 select GENERIC_SCHED_CLOCK
44 select GENERIC_SMP_IDLE_THREAD
45 select GENERIC_STRNCPY_FROM_USER
46 select GENERIC_STRNLEN_USER
47 select HANDLE_DOMAIN_IRQ
48 select HARDIRQS_SW_RESEND
49 select HAVE_ARCH_AUDITSYSCALL if (AEABI && !OABI_COMPAT)
50 select HAVE_ARCH_BITREVERSE if (CPU_32v7M || CPU_32v7) && !CPU_32v6
51 select HAVE_ARCH_JUMP_LABEL if !XIP_KERNEL && !CPU_ENDIAN_BE32 && MMU
52 select HAVE_ARCH_KGDB if !CPU_ENDIAN_BE32 && MMU
53 select HAVE_ARCH_MMAP_RND_BITS if MMU
54 select HAVE_ARCH_SECCOMP_FILTER if (AEABI && !OABI_COMPAT)
55 select HAVE_ARCH_THREAD_STRUCT_WHITELIST
56 select HAVE_ARCH_TRACEHOOK
57 select HAVE_ARM_SMCCC if CPU_V7
58 select HAVE_EBPF_JIT if !CPU_ENDIAN_BE32
59 select HAVE_CC_STACKPROTECTOR
60 select HAVE_CONTEXT_TRACKING
61 select HAVE_C_RECORDMCOUNT
62 select HAVE_DEBUG_KMEMLEAK
63 select HAVE_DMA_CONTIGUOUS if MMU
64 select HAVE_DYNAMIC_FTRACE if (!XIP_KERNEL) && !CPU_ENDIAN_BE32 && MMU
65 select HAVE_DYNAMIC_FTRACE_WITH_REGS if HAVE_DYNAMIC_FTRACE
66 select HAVE_EFFICIENT_UNALIGNED_ACCESS if (CPU_V6 || CPU_V6K || CPU_V7) && MMU
67 select HAVE_EXIT_THREAD
68 select HAVE_FTRACE_MCOUNT_RECORD if (!XIP_KERNEL)
69 select HAVE_FUNCTION_GRAPH_TRACER if (!THUMB2_KERNEL)
70 select HAVE_FUNCTION_TRACER if (!XIP_KERNEL)
71 select HAVE_GCC_PLUGINS
72 select HAVE_GENERIC_DMA_COHERENT
73 select HAVE_HW_BREAKPOINT if (PERF_EVENTS && (CPU_V6 || CPU_V6K || CPU_V7))
74 select HAVE_IDE if PCI || ISA || PCMCIA
75 select HAVE_IRQ_TIME_ACCOUNTING
76 select HAVE_KERNEL_GZIP
77 select HAVE_KERNEL_LZ4
78 select HAVE_KERNEL_LZMA
79 select HAVE_KERNEL_LZO
81 select HAVE_KPROBES if !XIP_KERNEL && !CPU_ENDIAN_BE32 && !CPU_V7M
82 select HAVE_KRETPROBES if (HAVE_KPROBES)
84 select HAVE_MOD_ARCH_SPECIFIC
86 select HAVE_OPROFILE if (HAVE_PERF_EVENTS)
87 select HAVE_OPTPROBES if !THUMB2_KERNEL
88 select HAVE_PERF_EVENTS
90 select HAVE_PERF_USER_STACK_DUMP
91 select HAVE_RCU_TABLE_FREE if (SMP && ARM_LPAE)
92 select HAVE_REGS_AND_STACK_ACCESS_API
93 select HAVE_SYSCALL_TRACEPOINTS
95 select HAVE_VIRT_CPU_ACCOUNTING_GEN
96 select IRQ_FORCED_THREADING
97 select MODULES_USE_ELF_REL
98 select NEED_DMA_MAP_STATE
100 select OF_EARLY_FLATTREE if OF
101 select OF_RESERVED_MEM if OF
103 select OLD_SIGSUSPEND3
104 select PERF_USE_VMALLOC
107 select SYS_SUPPORTS_APM_EMULATION
108 # Above selects are sorted alphabetically; please add new ones
109 # according to that. Thanks.
111 The ARM series is a line of low-power-consumption RISC chip designs
112 licensed by ARM Ltd and targeted at embedded applications and
113 handhelds such as the Compaq IPAQ. ARM-based PCs are no longer
114 manufactured, but legacy ARM-based PC hardware remains popular in
115 Europe. There is an ARM Linux project with a web page at
116 <http://www.arm.linux.org.uk/>.
118 config ARM_HAS_SG_CHAIN
119 select ARCH_HAS_SG_CHAIN
122 config ARM_DMA_USE_IOMMU
124 select ARM_HAS_SG_CHAIN
125 select NEED_SG_DMA_LENGTH
129 config ARM_DMA_IOMMU_ALIGNMENT
130 int "Maximum PAGE_SIZE order of alignment for DMA IOMMU buffers"
134 DMA mapping framework by default aligns all buffers to the smallest
135 PAGE_SIZE order which is greater than or equal to the requested buffer
136 size. This works well for buffers up to a few hundreds kilobytes, but
137 for larger buffers it just a waste of address space. Drivers which has
138 relatively small addressing window (like 64Mib) might run out of
139 virtual space with just a few allocations.
141 With this parameter you can specify the maximum PAGE_SIZE order for
142 DMA IOMMU buffers. Larger buffers will be aligned only to this
143 specified order. The order is expressed as a power of two multiplied
148 config MIGHT_HAVE_PCI
151 config SYS_SUPPORTS_APM_EMULATION
156 select GENERIC_ALLOCATOR
167 The Extended Industry Standard Architecture (EISA) bus was
168 developed as an open alternative to the IBM MicroChannel bus.
170 The EISA bus provided some of the features of the IBM MicroChannel
171 bus while maintaining backward compatibility with cards made for
172 the older ISA bus. The EISA bus saw limited use between 1988 and
173 1995 when it was made obsolete by the PCI bus.
175 Say Y here if you are building a kernel for an EISA-based machine.
182 config STACKTRACE_SUPPORT
186 config LOCKDEP_SUPPORT
190 config TRACE_IRQFLAGS_SUPPORT
194 config RWSEM_XCHGADD_ALGORITHM
198 config ARCH_HAS_ILOG2_U32
201 config ARCH_HAS_ILOG2_U64
204 config ARCH_HAS_BANDGAP
207 config FIX_EARLYCON_MEM
210 config GENERIC_HWEIGHT
214 config GENERIC_CALIBRATE_DELAY
218 config ARCH_MAY_HAVE_PC_FDC
224 config ARCH_SUPPORTS_UPROBES
227 config ARCH_HAS_DMA_SET_COHERENT_MASK
230 config GENERIC_ISA_DMA
236 config NEED_RET_TO_USER
242 config ARM_PATCH_PHYS_VIRT
243 bool "Patch physical to virtual translations at runtime" if EMBEDDED
245 depends on !XIP_KERNEL && MMU
247 Patch phys-to-virt and virt-to-phys translation functions at
248 boot and module load time according to the position of the
249 kernel in system memory.
251 This can only be used with non-XIP MMU kernels where the base
252 of physical memory is at a 16MB boundary.
254 Only disable this option if you know that you do not require
255 this feature (eg, building a kernel for a single machine) and
256 you need to shrink the kernel to the minimal size.
258 config NEED_MACH_IO_H
261 Select this when mach/io.h is required to provide special
262 definitions for this platform. The need for mach/io.h should
263 be avoided when possible.
265 config NEED_MACH_MEMORY_H
268 Select this when mach/memory.h is required to provide special
269 definitions for this platform. The need for mach/memory.h should
270 be avoided when possible.
273 hex "Physical address of main memory" if MMU
274 depends on !ARM_PATCH_PHYS_VIRT
275 default DRAM_BASE if !MMU
276 default 0x00000000 if ARCH_EBSA110 || \
282 default 0x10000000 if ARCH_OMAP1 || ARCH_RPC
283 default 0x20000000 if ARCH_S5PV210
284 default 0xc0000000 if ARCH_SA1100
286 Please provide the physical address corresponding to the
287 location of main memory in your system.
293 config PGTABLE_LEVELS
295 default 3 if ARM_LPAE
298 source "init/Kconfig"
300 source "kernel/Kconfig.freezer"
305 bool "MMU-based Paged Memory Management Support"
308 Select if you want MMU-based virtualised addressing space
309 support by paged memory management. If unsure, say 'Y'.
311 config ARCH_MMAP_RND_BITS_MIN
314 config ARCH_MMAP_RND_BITS_MAX
315 default 14 if PAGE_OFFSET=0x40000000
316 default 15 if PAGE_OFFSET=0x80000000
320 # The "ARM system type" choice list is ordered alphabetically by option
321 # text. Please add new entries in the option alphabetic order.
324 prompt "ARM system type"
325 default ARM_SINGLE_ARMV7M if !MMU
326 default ARCH_MULTIPLATFORM if MMU
328 config ARCH_MULTIPLATFORM
329 bool "Allow multiple platforms to be selected"
331 select ARM_HAS_SG_CHAIN
332 select ARM_PATCH_PHYS_VIRT
336 select GENERIC_CLOCKEVENTS
337 select MIGHT_HAVE_PCI
338 select MULTI_IRQ_HANDLER
339 select PCI_DOMAINS if PCI
343 config ARM_SINGLE_ARMV7M
344 bool "ARMv7-M based platforms (Cortex-M0/M3/M4)"
351 select GENERIC_CLOCKEVENTS
358 select ARCH_USES_GETTIMEOFFSET
361 select NEED_MACH_IO_H
362 select NEED_MACH_MEMORY_H
365 This is an evaluation board for the StrongARM processor available
366 from Digital. It has limited hardware on-board, including an
367 Ethernet interface, two PCMCIA sockets, two serial ports and a
372 select ARCH_SPARSEMEM_ENABLE
374 imply ARM_PATCH_PHYS_VIRT
380 select GENERIC_CLOCKEVENTS
383 This enables support for the Cirrus EP93xx series of CPUs.
385 config ARCH_FOOTBRIDGE
389 select GENERIC_CLOCKEVENTS
391 select NEED_MACH_IO_H if !MMU
392 select NEED_MACH_MEMORY_H
394 Support for systems based on the DC21285 companion chip
395 ("FootBridge"), such as the Simtec CATS and the Rebel NetWinder.
398 bool "Hilscher NetX based"
402 select GENERIC_CLOCKEVENTS
404 This enables support for systems based on the Hilscher NetX Soc
410 select NEED_MACH_MEMORY_H
411 select NEED_RET_TO_USER
417 Support for Intel's IOP13XX (XScale) family of processors.
425 select NEED_RET_TO_USER
429 Support for Intel's 80219 and IOP32X (XScale) family of
438 select NEED_RET_TO_USER
442 Support for Intel's IOP33X (XScale) family of processors.
447 select ARCH_HAS_DMA_SET_COHERENT_MASK
448 select ARCH_SUPPORTS_BIG_ENDIAN
451 select DMABOUNCE if PCI
452 select GENERIC_CLOCKEVENTS
454 select MIGHT_HAVE_PCI
455 select NEED_MACH_IO_H
456 select USB_EHCI_BIG_ENDIAN_DESC
457 select USB_EHCI_BIG_ENDIAN_MMIO
459 Support for Intel's IXP4XX (XScale) family of processors.
464 select GENERIC_CLOCKEVENTS
466 select MIGHT_HAVE_PCI
467 select MULTI_IRQ_HANDLER
471 select PLAT_ORION_LEGACY
473 select PM_GENERIC_DOMAINS if PM
475 Support for the Marvell Dove SoC 88AP510
478 bool "Micrel/Kendin KS8695"
481 select GENERIC_CLOCKEVENTS
483 select NEED_MACH_MEMORY_H
485 Support for Micrel/Kendin KS8695 "Centaur" (ARM922T) based
486 System-on-Chip devices.
489 bool "Nuvoton W90X900 CPU"
493 select GENERIC_CLOCKEVENTS
496 Support for Nuvoton (Winbond logic dept.) ARM9 processor,
497 At present, the w90x900 has been renamed nuc900, regarding
498 the ARM series product line, you can login the following
499 link address to know more.
501 <http://www.nuvoton.com/hq/enu/ProductAndSales/ProductLines/
502 ConsumerElectronicsIC/ARMMicrocontroller/ARMMicrocontroller>
508 select CLKSRC_LPC32XX
511 select GENERIC_CLOCKEVENTS
513 select MULTI_IRQ_HANDLER
517 Support for the NXP LPC32XX family of processors
520 bool "PXA2xx/PXA3xx-based"
523 select ARM_CPU_SUSPEND if PM
530 select CPU_XSCALE if !CPU_XSC3
531 select GENERIC_CLOCKEVENTS
536 select MULTI_IRQ_HANDLER
540 Support for Intel/Marvell's PXA2xx/PXA3xx processor line.
546 select ARCH_MAY_HAVE_PC_FDC
547 select ARCH_SPARSEMEM_ENABLE
548 select ARCH_USES_GETTIMEOFFSET
552 select HAVE_PATA_PLATFORM
554 select NEED_MACH_IO_H
555 select NEED_MACH_MEMORY_H
558 On the Acorn Risc-PC, Linux can support the internal IDE disk and
559 CD-ROM interface, serial and parallel port, and the floppy drive.
564 select ARCH_SPARSEMEM_ENABLE
568 select TIMER_OF if OF
571 select GENERIC_CLOCKEVENTS
576 select MULTI_IRQ_HANDLER
577 select NEED_MACH_MEMORY_H
580 Support for StrongARM 11x0 based boards.
583 bool "Samsung S3C24XX SoCs"
586 select CLKSRC_SAMSUNG_PWM
587 select GENERIC_CLOCKEVENTS
590 select HAVE_S3C2410_I2C if I2C
591 select HAVE_S3C2410_WATCHDOG if WATCHDOG
592 select HAVE_S3C_RTC if RTC_CLASS
593 select MULTI_IRQ_HANDLER
594 select NEED_MACH_IO_H
598 Samsung S3C2410, S3C2412, S3C2413, S3C2416, S3C2440, S3C2442, S3C2443
599 and S3C2450 SoCs based systems, such as the Simtec Electronics BAST
600 (<http://www.simtec.co.uk/products/EB110ITX/>), the IPAQ 1940 or the
601 Samsung SMDK2410 development board (and derivatives).
605 select ARCH_HAS_HOLES_MEMORYMODEL
608 select GENERIC_ALLOCATOR
609 select GENERIC_CLOCKEVENTS
610 select GENERIC_IRQ_CHIP
616 Support for TI's DaVinci platform.
621 select ARCH_HAS_HOLES_MEMORYMODEL
625 select GENERIC_CLOCKEVENTS
626 select GENERIC_IRQ_CHIP
630 select MULTI_IRQ_HANDLER
631 select NEED_MACH_IO_H if PCCARD
632 select NEED_MACH_MEMORY_H
635 Support for older TI OMAP1 (omap7xx, omap15xx or omap16xx)
639 menu "Multiple platform selection"
640 depends on ARCH_MULTIPLATFORM
642 comment "CPU Core family selection"
645 bool "ARMv4 based platforms (FA526)"
646 depends on !ARCH_MULTI_V6_V7
647 select ARCH_MULTI_V4_V5
650 config ARCH_MULTI_V4T
651 bool "ARMv4T based platforms (ARM720T, ARM920T, ...)"
652 depends on !ARCH_MULTI_V6_V7
653 select ARCH_MULTI_V4_V5
654 select CPU_ARM920T if !(CPU_ARM7TDMI || CPU_ARM720T || \
655 CPU_ARM740T || CPU_ARM9TDMI || CPU_ARM922T || \
656 CPU_ARM925T || CPU_ARM940T)
659 bool "ARMv5 based platforms (ARM926T, XSCALE, PJ1, ...)"
660 depends on !ARCH_MULTI_V6_V7
661 select ARCH_MULTI_V4_V5
662 select CPU_ARM926T if !(CPU_ARM946E || CPU_ARM1020 || \
663 CPU_ARM1020E || CPU_ARM1022 || CPU_ARM1026 || \
664 CPU_XSCALE || CPU_XSC3 || CPU_MOHAWK || CPU_FEROCEON)
666 config ARCH_MULTI_V4_V5
670 bool "ARMv6 based platforms (ARM11)"
671 select ARCH_MULTI_V6_V7
675 bool "ARMv7 based platforms (Cortex-A, PJ4, Scorpion, Krait)"
677 select ARCH_MULTI_V6_V7
681 config ARCH_MULTI_V6_V7
683 select MIGHT_HAVE_CACHE_L2X0
685 config ARCH_MULTI_CPU_AUTO
686 def_bool !(ARCH_MULTI_V4 || ARCH_MULTI_V4T || ARCH_MULTI_V6_V7)
692 bool "Dummy Virtual Machine"
693 depends on ARCH_MULTI_V7
696 select ARM_GIC_V2M if PCI
698 select ARM_GIC_V3_ITS if PCI
700 select HAVE_ARM_ARCH_TIMER
703 # This is sorted alphabetically by mach-* pathname. However, plat-*
704 # Kconfigs may be included either alphabetically (according to the
705 # plat- suffix) or along side the corresponding mach-* source.
707 source "arch/arm/mach-actions/Kconfig"
709 source "arch/arm/mach-alpine/Kconfig"
711 source "arch/arm/mach-artpec/Kconfig"
713 source "arch/arm/mach-asm9260/Kconfig"
715 source "arch/arm/mach-aspeed/Kconfig"
717 source "arch/arm/mach-at91/Kconfig"
719 source "arch/arm/mach-axxia/Kconfig"
721 source "arch/arm/mach-bcm/Kconfig"
723 source "arch/arm/mach-berlin/Kconfig"
725 source "arch/arm/mach-clps711x/Kconfig"
727 source "arch/arm/mach-cns3xxx/Kconfig"
729 source "arch/arm/mach-davinci/Kconfig"
731 source "arch/arm/mach-digicolor/Kconfig"
733 source "arch/arm/mach-dove/Kconfig"
735 source "arch/arm/mach-ep93xx/Kconfig"
737 source "arch/arm/mach-exynos/Kconfig"
738 source "arch/arm/plat-samsung/Kconfig"
740 source "arch/arm/mach-footbridge/Kconfig"
742 source "arch/arm/mach-gemini/Kconfig"
744 source "arch/arm/mach-highbank/Kconfig"
746 source "arch/arm/mach-hisi/Kconfig"
748 source "arch/arm/mach-imx/Kconfig"
750 source "arch/arm/mach-integrator/Kconfig"
752 source "arch/arm/mach-iop13xx/Kconfig"
754 source "arch/arm/mach-iop32x/Kconfig"
756 source "arch/arm/mach-iop33x/Kconfig"
758 source "arch/arm/mach-ixp4xx/Kconfig"
760 source "arch/arm/mach-keystone/Kconfig"
762 source "arch/arm/mach-ks8695/Kconfig"
764 source "arch/arm/mach-mediatek/Kconfig"
766 source "arch/arm/mach-meson/Kconfig"
768 source "arch/arm/mach-mmp/Kconfig"
770 source "arch/arm/mach-moxart/Kconfig"
772 source "arch/arm/mach-mv78xx0/Kconfig"
774 source "arch/arm/mach-mvebu/Kconfig"
776 source "arch/arm/mach-mxs/Kconfig"
778 source "arch/arm/mach-netx/Kconfig"
780 source "arch/arm/mach-nomadik/Kconfig"
782 source "arch/arm/mach-npcm/Kconfig"
784 source "arch/arm/mach-nspire/Kconfig"
786 source "arch/arm/plat-omap/Kconfig"
788 source "arch/arm/mach-omap1/Kconfig"
790 source "arch/arm/mach-omap2/Kconfig"
792 source "arch/arm/mach-orion5x/Kconfig"
794 source "arch/arm/mach-oxnas/Kconfig"
796 source "arch/arm/mach-picoxcell/Kconfig"
798 source "arch/arm/mach-prima2/Kconfig"
800 source "arch/arm/mach-pxa/Kconfig"
801 source "arch/arm/plat-pxa/Kconfig"
803 source "arch/arm/mach-qcom/Kconfig"
805 source "arch/arm/mach-realview/Kconfig"
807 source "arch/arm/mach-rockchip/Kconfig"
809 source "arch/arm/mach-s3c24xx/Kconfig"
811 source "arch/arm/mach-s3c64xx/Kconfig"
813 source "arch/arm/mach-s5pv210/Kconfig"
815 source "arch/arm/mach-sa1100/Kconfig"
817 source "arch/arm/mach-shmobile/Kconfig"
819 source "arch/arm/mach-socfpga/Kconfig"
821 source "arch/arm/mach-spear/Kconfig"
823 source "arch/arm/mach-sti/Kconfig"
825 source "arch/arm/mach-stm32/Kconfig"
827 source "arch/arm/mach-sunxi/Kconfig"
829 source "arch/arm/mach-tango/Kconfig"
831 source "arch/arm/mach-tegra/Kconfig"
833 source "arch/arm/mach-u300/Kconfig"
835 source "arch/arm/mach-uniphier/Kconfig"
837 source "arch/arm/mach-ux500/Kconfig"
839 source "arch/arm/mach-versatile/Kconfig"
841 source "arch/arm/mach-vexpress/Kconfig"
842 source "arch/arm/plat-versatile/Kconfig"
844 source "arch/arm/mach-vt8500/Kconfig"
846 source "arch/arm/mach-w90x900/Kconfig"
848 source "arch/arm/mach-zx/Kconfig"
850 source "arch/arm/mach-zynq/Kconfig"
852 # ARMv7-M architecture
854 bool "Energy Micro efm32"
855 depends on ARM_SINGLE_ARMV7M
858 Support for Energy Micro's (now Silicon Labs) efm32 Giant Gecko
862 bool "NXP LPC18xx/LPC43xx"
863 depends on ARM_SINGLE_ARMV7M
864 select ARCH_HAS_RESET_CONTROLLER
866 select CLKSRC_LPC32XX
869 Support for NXP's LPC18xx Cortex-M3 and LPC43xx Cortex-M4
870 high performance microcontrollers.
873 bool "ARM MPS2 platform"
874 depends on ARM_SINGLE_ARMV7M
878 Support for Cortex-M Prototyping System (or V2M-MPS2) which comes
879 with a range of available cores like Cortex-M3/M4/M7.
881 Please, note that depends which Application Note is used memory map
882 for the platform may vary, so adjustment of RAM base might be needed.
884 # Definitions to make life easier
890 select GENERIC_CLOCKEVENTS
896 select GENERIC_IRQ_CHIP
899 config PLAT_ORION_LEGACY
906 config PLAT_VERSATILE
909 source "arch/arm/firmware/Kconfig"
911 source arch/arm/mm/Kconfig
914 bool "Enable iWMMXt support"
915 depends on CPU_XSCALE || CPU_XSC3 || CPU_MOHAWK || CPU_PJ4 || CPU_PJ4B
916 default y if PXA27x || PXA3xx || ARCH_MMP || CPU_PJ4 || CPU_PJ4B
918 Enable support for iWMMXt context switching at run time if
919 running on a CPU that supports it.
921 config MULTI_IRQ_HANDLER
924 Allow each machine to specify it's own IRQ handler at run time.
927 source "arch/arm/Kconfig-nommu"
930 config PJ4B_ERRATA_4742
931 bool "PJ4B Errata 4742: IDLE Wake Up Commands can Cause the CPU Core to Cease Operation"
932 depends on CPU_PJ4B && MACH_ARMADA_370
935 When coming out of either a Wait for Interrupt (WFI) or a Wait for
936 Event (WFE) IDLE states, a specific timing sensitivity exists between
937 the retiring WFI/WFE instructions and the newly issued subsequent
938 instructions. This sensitivity can result in a CPU hang scenario.
940 The software must insert either a Data Synchronization Barrier (DSB)
941 or Data Memory Barrier (DMB) command immediately after the WFI/WFE
944 config ARM_ERRATA_326103
945 bool "ARM errata: FSR write bit incorrect on a SWP to read-only memory"
948 Executing a SWP instruction to read-only memory does not set bit 11
949 of the FSR on the ARM 1136 prior to r1p0. This causes the kernel to
950 treat the access as a read, preventing a COW from occurring and
951 causing the faulting task to livelock.
953 config ARM_ERRATA_411920
954 bool "ARM errata: Invalidation of the Instruction Cache operation can fail"
955 depends on CPU_V6 || CPU_V6K
957 Invalidation of the Instruction Cache operation can
958 fail. This erratum is present in 1136 (before r1p4), 1156 and 1176.
959 It does not affect the MPCore. This option enables the ARM Ltd.
960 recommended workaround.
962 config ARM_ERRATA_430973
963 bool "ARM errata: Stale prediction on replaced interworking branch"
966 This option enables the workaround for the 430973 Cortex-A8
967 r1p* erratum. If a code sequence containing an ARM/Thumb
968 interworking branch is replaced with another code sequence at the
969 same virtual address, whether due to self-modifying code or virtual
970 to physical address re-mapping, Cortex-A8 does not recover from the
971 stale interworking branch prediction. This results in Cortex-A8
972 executing the new code sequence in the incorrect ARM or Thumb state.
973 The workaround enables the BTB/BTAC operations by setting ACTLR.IBE
974 and also flushes the branch target cache at every context switch.
975 Note that setting specific bits in the ACTLR register may not be
976 available in non-secure mode.
978 config ARM_ERRATA_458693
979 bool "ARM errata: Processor deadlock when a false hazard is created"
981 depends on !ARCH_MULTIPLATFORM
983 This option enables the workaround for the 458693 Cortex-A8 (r2p0)
984 erratum. For very specific sequences of memory operations, it is
985 possible for a hazard condition intended for a cache line to instead
986 be incorrectly associated with a different cache line. This false
987 hazard might then cause a processor deadlock. The workaround enables
988 the L1 caching of the NEON accesses and disables the PLD instruction
989 in the ACTLR register. Note that setting specific bits in the ACTLR
990 register may not be available in non-secure mode.
992 config ARM_ERRATA_460075
993 bool "ARM errata: Data written to the L2 cache can be overwritten with stale data"
995 depends on !ARCH_MULTIPLATFORM
997 This option enables the workaround for the 460075 Cortex-A8 (r2p0)
998 erratum. Any asynchronous access to the L2 cache may encounter a
999 situation in which recent store transactions to the L2 cache are lost
1000 and overwritten with stale memory contents from external memory. The
1001 workaround disables the write-allocate mode for the L2 cache via the
1002 ACTLR register. Note that setting specific bits in the ACTLR register
1003 may not be available in non-secure mode.
1005 config ARM_ERRATA_742230
1006 bool "ARM errata: DMB operation may be faulty"
1007 depends on CPU_V7 && SMP
1008 depends on !ARCH_MULTIPLATFORM
1010 This option enables the workaround for the 742230 Cortex-A9
1011 (r1p0..r2p2) erratum. Under rare circumstances, a DMB instruction
1012 between two write operations may not ensure the correct visibility
1013 ordering of the two writes. This workaround sets a specific bit in
1014 the diagnostic register of the Cortex-A9 which causes the DMB
1015 instruction to behave as a DSB, ensuring the correct behaviour of
1018 config ARM_ERRATA_742231
1019 bool "ARM errata: Incorrect hazard handling in the SCU may lead to data corruption"
1020 depends on CPU_V7 && SMP
1021 depends on !ARCH_MULTIPLATFORM
1023 This option enables the workaround for the 742231 Cortex-A9
1024 (r2p0..r2p2) erratum. Under certain conditions, specific to the
1025 Cortex-A9 MPCore micro-architecture, two CPUs working in SMP mode,
1026 accessing some data located in the same cache line, may get corrupted
1027 data due to bad handling of the address hazard when the line gets
1028 replaced from one of the CPUs at the same time as another CPU is
1029 accessing it. This workaround sets specific bits in the diagnostic
1030 register of the Cortex-A9 which reduces the linefill issuing
1031 capabilities of the processor.
1033 config ARM_ERRATA_643719
1034 bool "ARM errata: LoUIS bit field in CLIDR register is incorrect"
1035 depends on CPU_V7 && SMP
1038 This option enables the workaround for the 643719 Cortex-A9 (prior to
1039 r1p0) erratum. On affected cores the LoUIS bit field of the CLIDR
1040 register returns zero when it should return one. The workaround
1041 corrects this value, ensuring cache maintenance operations which use
1042 it behave as intended and avoiding data corruption.
1044 config ARM_ERRATA_720789
1045 bool "ARM errata: TLBIASIDIS and TLBIMVAIS operations can broadcast a faulty ASID"
1048 This option enables the workaround for the 720789 Cortex-A9 (prior to
1049 r2p0) erratum. A faulty ASID can be sent to the other CPUs for the
1050 broadcasted CP15 TLB maintenance operations TLBIASIDIS and TLBIMVAIS.
1051 As a consequence of this erratum, some TLB entries which should be
1052 invalidated are not, resulting in an incoherency in the system page
1053 tables. The workaround changes the TLB flushing routines to invalidate
1054 entries regardless of the ASID.
1056 config ARM_ERRATA_743622
1057 bool "ARM errata: Faulty hazard checking in the Store Buffer may lead to data corruption"
1059 depends on !ARCH_MULTIPLATFORM
1061 This option enables the workaround for the 743622 Cortex-A9
1062 (r2p*) erratum. Under very rare conditions, a faulty
1063 optimisation in the Cortex-A9 Store Buffer may lead to data
1064 corruption. This workaround sets a specific bit in the diagnostic
1065 register of the Cortex-A9 which disables the Store Buffer
1066 optimisation, preventing the defect from occurring. This has no
1067 visible impact on the overall performance or power consumption of the
1070 config ARM_ERRATA_751472
1071 bool "ARM errata: Interrupted ICIALLUIS may prevent completion of broadcasted operation"
1073 depends on !ARCH_MULTIPLATFORM
1075 This option enables the workaround for the 751472 Cortex-A9 (prior
1076 to r3p0) erratum. An interrupted ICIALLUIS operation may prevent the
1077 completion of a following broadcasted operation if the second
1078 operation is received by a CPU before the ICIALLUIS has completed,
1079 potentially leading to corrupted entries in the cache or TLB.
1081 config ARM_ERRATA_754322
1082 bool "ARM errata: possible faulty MMU translations following an ASID switch"
1085 This option enables the workaround for the 754322 Cortex-A9 (r2p*,
1086 r3p*) erratum. A speculative memory access may cause a page table walk
1087 which starts prior to an ASID switch but completes afterwards. This
1088 can populate the micro-TLB with a stale entry which may be hit with
1089 the new ASID. This workaround places two dsb instructions in the mm
1090 switching code so that no page table walks can cross the ASID switch.
1092 config ARM_ERRATA_754327
1093 bool "ARM errata: no automatic Store Buffer drain"
1094 depends on CPU_V7 && SMP
1096 This option enables the workaround for the 754327 Cortex-A9 (prior to
1097 r2p0) erratum. The Store Buffer does not have any automatic draining
1098 mechanism and therefore a livelock may occur if an external agent
1099 continuously polls a memory location waiting to observe an update.
1100 This workaround defines cpu_relax() as smp_mb(), preventing correctly
1101 written polling loops from denying visibility of updates to memory.
1103 config ARM_ERRATA_364296
1104 bool "ARM errata: Possible cache data corruption with hit-under-miss enabled"
1107 This options enables the workaround for the 364296 ARM1136
1108 r0p2 erratum (possible cache data corruption with
1109 hit-under-miss enabled). It sets the undocumented bit 31 in
1110 the auxiliary control register and the FI bit in the control
1111 register, thus disabling hit-under-miss without putting the
1112 processor into full low interrupt latency mode. ARM11MPCore
1115 config ARM_ERRATA_764369
1116 bool "ARM errata: Data cache line maintenance operation by MVA may not succeed"
1117 depends on CPU_V7 && SMP
1119 This option enables the workaround for erratum 764369
1120 affecting Cortex-A9 MPCore with two or more processors (all
1121 current revisions). Under certain timing circumstances, a data
1122 cache line maintenance operation by MVA targeting an Inner
1123 Shareable memory region may fail to proceed up to either the
1124 Point of Coherency or to the Point of Unification of the
1125 system. This workaround adds a DSB instruction before the
1126 relevant cache maintenance functions and sets a specific bit
1127 in the diagnostic control register of the SCU.
1129 config ARM_ERRATA_775420
1130 bool "ARM errata: A data cache maintenance operation which aborts, might lead to deadlock"
1133 This option enables the workaround for the 775420 Cortex-A9 (r2p2,
1134 r2p6,r2p8,r2p10,r3p0) erratum. In case a date cache maintenance
1135 operation aborts with MMU exception, it might cause the processor
1136 to deadlock. This workaround puts DSB before executing ISB if
1137 an abort may occur on cache maintenance.
1139 config ARM_ERRATA_798181
1140 bool "ARM errata: TLBI/DSB failure on Cortex-A15"
1141 depends on CPU_V7 && SMP
1143 On Cortex-A15 (r0p0..r3p2) the TLBI*IS/DSB operations are not
1144 adequately shooting down all use of the old entries. This
1145 option enables the Linux kernel workaround for this erratum
1146 which sends an IPI to the CPUs that are running the same ASID
1147 as the one being invalidated.
1149 config ARM_ERRATA_773022
1150 bool "ARM errata: incorrect instructions may be executed from loop buffer"
1153 This option enables the workaround for the 773022 Cortex-A15
1154 (up to r0p4) erratum. In certain rare sequences of code, the
1155 loop buffer may deliver incorrect instructions. This
1156 workaround disables the loop buffer to avoid the erratum.
1158 config ARM_ERRATA_818325_852422
1159 bool "ARM errata: A12: some seqs of opposed cond code instrs => deadlock or corruption"
1162 This option enables the workaround for:
1163 - Cortex-A12 818325: Execution of an UNPREDICTABLE STR or STM
1164 instruction might deadlock. Fixed in r0p1.
1165 - Cortex-A12 852422: Execution of a sequence of instructions might
1166 lead to either a data corruption or a CPU deadlock. Not fixed in
1167 any Cortex-A12 cores yet.
1168 This workaround for all both errata involves setting bit[12] of the
1169 Feature Register. This bit disables an optimisation applied to a
1170 sequence of 2 instructions that use opposing condition codes.
1172 config ARM_ERRATA_821420
1173 bool "ARM errata: A12: sequence of VMOV to core registers might lead to a dead lock"
1176 This option enables the workaround for the 821420 Cortex-A12
1177 (all revs) erratum. In very rare timing conditions, a sequence
1178 of VMOV to Core registers instructions, for which the second
1179 one is in the shadow of a branch or abort, can lead to a
1180 deadlock when the VMOV instructions are issued out-of-order.
1182 config ARM_ERRATA_825619
1183 bool "ARM errata: A12: DMB NSHST/ISHST mixed ... might cause deadlock"
1186 This option enables the workaround for the 825619 Cortex-A12
1187 (all revs) erratum. Within rare timing constraints, executing a
1188 DMB NSHST or DMB ISHST instruction followed by a mix of Cacheable
1189 and Device/Strongly-Ordered loads and stores might cause deadlock
1191 config ARM_ERRATA_852421
1192 bool "ARM errata: A17: DMB ST might fail to create order between stores"
1195 This option enables the workaround for the 852421 Cortex-A17
1196 (r1p0, r1p1, r1p2) erratum. Under very rare timing conditions,
1197 execution of a DMB ST instruction might fail to properly order
1198 stores from GroupA and stores from GroupB.
1200 config ARM_ERRATA_852423
1201 bool "ARM errata: A17: some seqs of opposed cond code instrs => deadlock or corruption"
1204 This option enables the workaround for:
1205 - Cortex-A17 852423: Execution of a sequence of instructions might
1206 lead to either a data corruption or a CPU deadlock. Not fixed in
1207 any Cortex-A17 cores yet.
1208 This is identical to Cortex-A12 erratum 852422. It is a separate
1209 config option from the A12 erratum due to the way errata are checked
1214 source "arch/arm/common/Kconfig"
1221 Find out whether you have ISA slots on your motherboard. ISA is the
1222 name of a bus system, i.e. the way the CPU talks to the other stuff
1223 inside your box. Other bus systems are PCI, EISA, MicroChannel
1224 (MCA) or VESA. ISA is an older system, now being displaced by PCI;
1225 newer boards don't support it. If you have ISA, say Y, otherwise N.
1227 # Select ISA DMA controller support
1232 # Select ISA DMA interface
1237 bool "PCI support" if MIGHT_HAVE_PCI
1239 Find out whether you have a PCI motherboard. PCI is the name of a
1240 bus system, i.e. the way the CPU talks to the other stuff inside
1241 your box. Other bus systems are ISA, EISA, MicroChannel (MCA) or
1242 VESA. If you have PCI, say Y, otherwise N.
1248 config PCI_DOMAINS_GENERIC
1249 def_bool PCI_DOMAINS
1251 config PCI_NANOENGINE
1252 bool "BSE nanoEngine PCI support"
1253 depends on SA1100_NANOENGINE
1255 Enable PCI on the BSE nanoEngine board.
1260 config PCI_HOST_ITE8152
1262 depends on PCI && MACH_ARMCORE
1266 source "drivers/pci/Kconfig"
1268 source "drivers/pcmcia/Kconfig"
1272 menu "Kernel Features"
1277 This option should be selected by machines which have an SMP-
1280 The only effect of this option is to make the SMP-related
1281 options available to the user for configuration.
1284 bool "Symmetric Multi-Processing"
1285 depends on CPU_V6K || CPU_V7
1286 depends on GENERIC_CLOCKEVENTS
1288 depends on MMU || ARM_MPU
1291 This enables support for systems with more than one CPU. If you have
1292 a system with only one CPU, say N. If you have a system with more
1293 than one CPU, say Y.
1295 If you say N here, the kernel will run on uni- and multiprocessor
1296 machines, but will use only one CPU of a multiprocessor machine. If
1297 you say Y here, the kernel will run on many, but not all,
1298 uniprocessor machines. On a uniprocessor machine, the kernel
1299 will run faster if you say N here.
1301 See also <file:Documentation/x86/i386/IO-APIC.txt>,
1302 <file:Documentation/nmi_watchdog.txt> and the SMP-HOWTO available at
1303 <http://tldp.org/HOWTO/SMP-HOWTO.html>.
1305 If you don't know what to do here, say N.
1308 bool "Allow booting SMP kernel on uniprocessor systems"
1309 depends on SMP && !XIP_KERNEL && MMU
1312 SMP kernels contain instructions which fail on non-SMP processors.
1313 Enabling this option allows the kernel to modify itself to make
1314 these instructions safe. Disabling it allows about 1K of space
1317 If you don't know what to do here, say Y.
1319 config ARM_CPU_TOPOLOGY
1320 bool "Support cpu topology definition"
1321 depends on SMP && CPU_V7
1324 Support ARM cpu topology definition. The MPIDR register defines
1325 affinity between processors which is then used to describe the cpu
1326 topology of an ARM System.
1329 bool "Multi-core scheduler support"
1330 depends on ARM_CPU_TOPOLOGY
1332 Multi-core scheduler support improves the CPU scheduler's decision
1333 making when dealing with multi-core CPU chips at a cost of slightly
1334 increased overhead in some places. If unsure say N here.
1337 bool "SMT scheduler support"
1338 depends on ARM_CPU_TOPOLOGY
1340 Improves the CPU scheduler's decision making when dealing with
1341 MultiThreading at a cost of slightly increased overhead in some
1342 places. If unsure say N here.
1347 This option enables support for the ARM system coherency unit
1349 config HAVE_ARM_ARCH_TIMER
1350 bool "Architected timer support"
1352 select ARM_ARCH_TIMER
1353 select GENERIC_CLOCKEVENTS
1355 This option enables support for the ARM architected timer
1359 select TIMER_OF if OF
1361 This options enables support for the ARM timer and watchdog unit
1364 bool "Multi-Cluster Power Management"
1365 depends on CPU_V7 && SMP
1367 This option provides the common power management infrastructure
1368 for (multi-)cluster based systems, such as big.LITTLE based
1371 config MCPM_QUAD_CLUSTER
1375 To avoid wasting resources unnecessarily, MCPM only supports up
1376 to 2 clusters by default.
1377 Platforms with 3 or 4 clusters that use MCPM must select this
1378 option to allow the additional clusters to be managed.
1381 bool "big.LITTLE support (Experimental)"
1382 depends on CPU_V7 && SMP
1385 This option enables support selections for the big.LITTLE
1386 system architecture.
1389 bool "big.LITTLE switcher support"
1390 depends on BIG_LITTLE && MCPM && HOTPLUG_CPU && ARM_GIC
1393 The big.LITTLE "switcher" provides the core functionality to
1394 transparently handle transition between a cluster of A15's
1395 and a cluster of A7's in a big.LITTLE system.
1397 config BL_SWITCHER_DUMMY_IF
1398 tristate "Simple big.LITTLE switcher user interface"
1399 depends on BL_SWITCHER && DEBUG_KERNEL
1401 This is a simple and dummy char dev interface to control
1402 the big.LITTLE switcher core code. It is meant for
1403 debugging purposes only.
1406 prompt "Memory split"
1410 Select the desired split between kernel and user memory.
1412 If you are not absolutely sure what you are doing, leave this
1416 bool "3G/1G user/kernel split"
1417 config VMSPLIT_3G_OPT
1418 depends on !ARM_LPAE
1419 bool "3G/1G user/kernel split (for full 1G low memory)"
1421 bool "2G/2G user/kernel split"
1423 bool "1G/3G user/kernel split"
1428 default PHYS_OFFSET if !MMU
1429 default 0x40000000 if VMSPLIT_1G
1430 default 0x80000000 if VMSPLIT_2G
1431 default 0xB0000000 if VMSPLIT_3G_OPT
1435 int "Maximum number of CPUs (2-32)"
1441 bool "Support for hot-pluggable CPUs"
1444 Say Y here to experiment with turning CPUs off and on. CPUs
1445 can be controlled through /sys/devices/system/cpu.
1448 bool "Support for the ARM Power State Coordination Interface (PSCI)"
1449 depends on HAVE_ARM_SMCCC
1452 Say Y here if you want Linux to communicate with system firmware
1453 implementing the PSCI specification for CPU-centric power
1454 management operations described in ARM document number ARM DEN
1455 0022A ("Power State Coordination Interface System Software on
1458 # The GPIO number here must be sorted by descending number. In case of
1459 # a multiplatform kernel, we just want the highest value required by the
1460 # selected platforms.
1463 default 2048 if ARCH_SOCFPGA
1464 default 1024 if ARCH_BRCMSTB || ARCH_SHMOBILE || ARCH_TEGRA || \
1466 default 512 if ARCH_EXYNOS || ARCH_KEYSTONE || SOC_OMAP5 || \
1467 SOC_DRA7XX || ARCH_S3C24XX || ARCH_S3C64XX || ARCH_S5PV210
1468 default 416 if ARCH_SUNXI
1469 default 392 if ARCH_U8500
1470 default 352 if ARCH_VT8500
1471 default 288 if ARCH_ROCKCHIP
1472 default 264 if MACH_H4700
1475 Maximum number of GPIOs in the system.
1477 If unsure, leave the default value.
1479 source kernel/Kconfig.preempt
1483 default 200 if ARCH_EBSA110
1484 default 128 if SOC_AT91RM9200
1488 depends on HZ_FIXED = 0
1489 prompt "Timer frequency"
1513 default HZ_FIXED if HZ_FIXED != 0
1514 default 100 if HZ_100
1515 default 200 if HZ_200
1516 default 250 if HZ_250
1517 default 300 if HZ_300
1518 default 500 if HZ_500
1522 def_bool HIGH_RES_TIMERS
1524 config THUMB2_KERNEL
1525 bool "Compile the kernel in Thumb-2 mode" if !CPU_THUMBONLY
1526 depends on (CPU_V7 || CPU_V7M) && !CPU_V6 && !CPU_V6K
1527 default y if CPU_THUMBONLY
1530 By enabling this option, the kernel will be compiled in
1535 config THUMB2_AVOID_R_ARM_THM_JUMP11
1536 bool "Work around buggy Thumb-2 short branch relocations in gas"
1537 depends on THUMB2_KERNEL && MODULES
1540 Various binutils versions can resolve Thumb-2 branches to
1541 locally-defined, preemptible global symbols as short-range "b.n"
1542 branch instructions.
1544 This is a problem, because there's no guarantee the final
1545 destination of the symbol, or any candidate locations for a
1546 trampoline, are within range of the branch. For this reason, the
1547 kernel does not support fixing up the R_ARM_THM_JUMP11 (102)
1548 relocation in modules at all, and it makes little sense to add
1551 The symptom is that the kernel fails with an "unsupported
1552 relocation" error when loading some modules.
1554 Until fixed tools are available, passing
1555 -fno-optimize-sibling-calls to gcc should prevent gcc generating
1556 code which hits this problem, at the cost of a bit of extra runtime
1557 stack usage in some cases.
1559 The problem is described in more detail at:
1560 https://bugs.launchpad.net/binutils-linaro/+bug/725126
1562 Only Thumb-2 kernels are affected.
1564 Unless you are sure your tools don't have this problem, say Y.
1566 config ARM_PATCH_IDIV
1567 bool "Runtime patch udiv/sdiv instructions into __aeabi_{u}idiv()"
1568 depends on CPU_32v7 && !XIP_KERNEL
1571 The ARM compiler inserts calls to __aeabi_idiv() and
1572 __aeabi_uidiv() when it needs to perform division on signed
1573 and unsigned integers. Some v7 CPUs have support for the sdiv
1574 and udiv instructions that can be used to implement those
1577 Enabling this option allows the kernel to modify itself to
1578 replace the first two instructions of these library functions
1579 with the sdiv or udiv plus "bx lr" instructions when the CPU
1580 it is running on supports them. Typically this will be faster
1581 and less power intensive than running the original library
1582 code to do integer division.
1585 bool "Use the ARM EABI to compile the kernel" if !CPU_V7 && !CPU_V7M && !CPU_V6 && !CPU_V6K
1586 default CPU_V7 || CPU_V7M || CPU_V6 || CPU_V6K
1588 This option allows for the kernel to be compiled using the latest
1589 ARM ABI (aka EABI). This is only useful if you are using a user
1590 space environment that is also compiled with EABI.
1592 Since there are major incompatibilities between the legacy ABI and
1593 EABI, especially with regard to structure member alignment, this
1594 option also changes the kernel syscall calling convention to
1595 disambiguate both ABIs and allow for backward compatibility support
1596 (selected with CONFIG_OABI_COMPAT).
1598 To use this you need GCC version 4.0.0 or later.
1601 bool "Allow old ABI binaries to run with this kernel (EXPERIMENTAL)"
1602 depends on AEABI && !THUMB2_KERNEL
1604 This option preserves the old syscall interface along with the
1605 new (ARM EABI) one. It also provides a compatibility layer to
1606 intercept syscalls that have structure arguments which layout
1607 in memory differs between the legacy ABI and the new ARM EABI
1608 (only for non "thumb" binaries). This option adds a tiny
1609 overhead to all syscalls and produces a slightly larger kernel.
1611 The seccomp filter system will not be available when this is
1612 selected, since there is no way yet to sensibly distinguish
1613 between calling conventions during filtering.
1615 If you know you'll be using only pure EABI user space then you
1616 can say N here. If this option is not selected and you attempt
1617 to execute a legacy ABI binary then the result will be
1618 UNPREDICTABLE (in fact it can be predicted that it won't work
1619 at all). If in doubt say N.
1621 config ARCH_HAS_HOLES_MEMORYMODEL
1624 config ARCH_SPARSEMEM_ENABLE
1627 config ARCH_SPARSEMEM_DEFAULT
1628 def_bool ARCH_SPARSEMEM_ENABLE
1630 config ARCH_SELECT_MEMORY_MODEL
1631 def_bool ARCH_SPARSEMEM_ENABLE
1633 config HAVE_ARCH_PFN_VALID
1634 def_bool ARCH_HAS_HOLES_MEMORYMODEL || !SPARSEMEM
1636 config HAVE_GENERIC_GUP
1641 bool "High Memory Support"
1644 The address space of ARM processors is only 4 Gigabytes large
1645 and it has to accommodate user address space, kernel address
1646 space as well as some memory mapped IO. That means that, if you
1647 have a large amount of physical memory and/or IO, not all of the
1648 memory can be "permanently mapped" by the kernel. The physical
1649 memory that is not permanently mapped is called "high memory".
1651 Depending on the selected kernel/user memory split, minimum
1652 vmalloc space and actual amount of RAM, you may not need this
1653 option which should result in a slightly faster kernel.
1658 bool "Allocate 2nd-level pagetables from highmem" if EXPERT
1662 The VM uses one page of physical memory for each page table.
1663 For systems with a lot of processes, this can use a lot of
1664 precious low memory, eventually leading to low memory being
1665 consumed by page tables. Setting this option will allow
1666 user-space 2nd level page tables to reside in high memory.
1668 config CPU_SW_DOMAIN_PAN
1669 bool "Enable use of CPU domains to implement privileged no-access"
1670 depends on MMU && !ARM_LPAE
1673 Increase kernel security by ensuring that normal kernel accesses
1674 are unable to access userspace addresses. This can help prevent
1675 use-after-free bugs becoming an exploitable privilege escalation
1676 by ensuring that magic values (such as LIST_POISON) will always
1677 fault when dereferenced.
1679 CPUs with low-vector mappings use a best-efforts implementation.
1680 Their lower 1MB needs to remain accessible for the vectors, but
1681 the remainder of userspace will become appropriately inaccessible.
1683 config HW_PERF_EVENTS
1687 config SYS_SUPPORTS_HUGETLBFS
1691 config HAVE_ARCH_TRANSPARENT_HUGEPAGE
1695 config ARCH_WANT_GENERAL_HUGETLB
1698 config ARM_MODULE_PLTS
1699 bool "Use PLTs to allow module memory to spill over into vmalloc area"
1703 Allocate PLTs when loading modules so that jumps and calls whose
1704 targets are too far away for their relative offsets to be encoded
1705 in the instructions themselves can be bounced via veneers in the
1706 module's PLT. This allows modules to be allocated in the generic
1707 vmalloc area after the dedicated module memory area has been
1708 exhausted. The modules will use slightly more memory, but after
1709 rounding up to page size, the actual memory footprint is usually
1712 Disabling this is usually safe for small single-platform
1713 configurations. If unsure, say y.
1717 config FORCE_MAX_ZONEORDER
1718 int "Maximum zone order"
1719 default "12" if SOC_AM33XX
1720 default "9" if SA1111 || ARCH_EFM32
1723 The kernel memory allocator divides physically contiguous memory
1724 blocks into "zones", where each zone is a power of two number of
1725 pages. This option selects the largest power of two that the kernel
1726 keeps in the memory allocator. If you need to allocate very large
1727 blocks of physically contiguous memory, then you may need to
1728 increase this value.
1730 This config option is actually maximum order plus one. For example,
1731 a value of 11 means that the largest free memory block is 2^10 pages.
1733 config ALIGNMENT_TRAP
1735 depends on CPU_CP15_MMU
1736 default y if !ARCH_EBSA110
1737 select HAVE_PROC_CPU if PROC_FS
1739 ARM processors cannot fetch/store information which is not
1740 naturally aligned on the bus, i.e., a 4 byte fetch must start at an
1741 address divisible by 4. On 32-bit ARM processors, these non-aligned
1742 fetch/store instructions will be emulated in software if you say
1743 here, which has a severe performance impact. This is necessary for
1744 correct operation of some network protocols. With an IP-only
1745 configuration it is safe to say N, otherwise say Y.
1747 config UACCESS_WITH_MEMCPY
1748 bool "Use kernel mem{cpy,set}() for {copy_to,clear}_user()"
1750 default y if CPU_FEROCEON
1752 Implement faster copy_to_user and clear_user methods for CPU
1753 cores where a 8-word STM instruction give significantly higher
1754 memory write throughput than a sequence of individual 32bit stores.
1756 A possible side effect is a slight increase in scheduling latency
1757 between threads sharing the same address space if they invoke
1758 such copy operations with large buffers.
1760 However, if the CPU data cache is using a write-allocate mode,
1761 this option is unlikely to provide any performance gain.
1765 prompt "Enable seccomp to safely compute untrusted bytecode"
1767 This kernel feature is useful for number crunching applications
1768 that may need to compute untrusted bytecode during their
1769 execution. By using pipes or other transports made available to
1770 the process as file descriptors supporting the read/write
1771 syscalls, it's possible to isolate those applications in
1772 their own address space using seccomp. Once seccomp is
1773 enabled via prctl(PR_SET_SECCOMP), it cannot be disabled
1774 and the task is only allowed to execute a few safe syscalls
1775 defined by each seccomp mode.
1778 bool "Enable paravirtualization code"
1780 This changes the kernel so it can modify itself when it is run
1781 under a hypervisor, potentially improving performance significantly
1782 over full virtualization.
1784 config PARAVIRT_TIME_ACCOUNTING
1785 bool "Paravirtual steal time accounting"
1789 Select this option to enable fine granularity task steal time
1790 accounting. Time spent executing other tasks in parallel with
1791 the current vCPU is discounted from the vCPU power. To account for
1792 that, there can be a small performance impact.
1794 If in doubt, say N here.
1801 bool "Xen guest support on ARM"
1802 depends on ARM && AEABI && OF
1803 depends on CPU_V7 && !CPU_V6
1804 depends on !GENERIC_ATOMIC64
1806 select ARCH_DMA_ADDR_T_64BIT
1812 Say Y if you want to run Linux in a Virtual Machine on Xen on ARM.
1819 bool "Flattened Device Tree support"
1823 Include support for flattened device tree machine descriptions.
1826 bool "Support for the traditional ATAGS boot data passing" if USE_OF
1829 This is the traditional way of passing data to the kernel at boot
1830 time. If you are solely relying on the flattened device tree (or
1831 the ARM_ATAG_DTB_COMPAT option) then you may unselect this option
1832 to remove ATAGS support from your kernel binary. If unsure,
1835 config DEPRECATED_PARAM_STRUCT
1836 bool "Provide old way to pass kernel parameters"
1839 This was deprecated in 2001 and announced to live on for 5 years.
1840 Some old boot loaders still use this way.
1842 # Compressed boot loader in ROM. Yes, we really want to ask about
1843 # TEXT and BSS so we preserve their values in the config files.
1844 config ZBOOT_ROM_TEXT
1845 hex "Compressed ROM boot loader base address"
1848 The physical address at which the ROM-able zImage is to be
1849 placed in the target. Platforms which normally make use of
1850 ROM-able zImage formats normally set this to a suitable
1851 value in their defconfig file.
1853 If ZBOOT_ROM is not enabled, this has no effect.
1855 config ZBOOT_ROM_BSS
1856 hex "Compressed ROM boot loader BSS address"
1859 The base address of an area of read/write memory in the target
1860 for the ROM-able zImage which must be available while the
1861 decompressor is running. It must be large enough to hold the
1862 entire decompressed kernel plus an additional 128 KiB.
1863 Platforms which normally make use of ROM-able zImage formats
1864 normally set this to a suitable value in their defconfig file.
1866 If ZBOOT_ROM is not enabled, this has no effect.
1869 bool "Compressed boot loader in ROM/flash"
1870 depends on ZBOOT_ROM_TEXT != ZBOOT_ROM_BSS
1871 depends on !ARM_APPENDED_DTB && !XIP_KERNEL && !AUTO_ZRELADDR
1873 Say Y here if you intend to execute your compressed kernel image
1874 (zImage) directly from ROM or flash. If unsure, say N.
1876 config ARM_APPENDED_DTB
1877 bool "Use appended device tree blob to zImage (EXPERIMENTAL)"
1880 With this option, the boot code will look for a device tree binary
1881 (DTB) appended to zImage
1882 (e.g. cat zImage <filename>.dtb > zImage_w_dtb).
1884 This is meant as a backward compatibility convenience for those
1885 systems with a bootloader that can't be upgraded to accommodate
1886 the documented boot protocol using a device tree.
1888 Beware that there is very little in terms of protection against
1889 this option being confused by leftover garbage in memory that might
1890 look like a DTB header after a reboot if no actual DTB is appended
1891 to zImage. Do not leave this option active in a production kernel
1892 if you don't intend to always append a DTB. Proper passing of the
1893 location into r2 of a bootloader provided DTB is always preferable
1896 config ARM_ATAG_DTB_COMPAT
1897 bool "Supplement the appended DTB with traditional ATAG information"
1898 depends on ARM_APPENDED_DTB
1900 Some old bootloaders can't be updated to a DTB capable one, yet
1901 they provide ATAGs with memory configuration, the ramdisk address,
1902 the kernel cmdline string, etc. Such information is dynamically
1903 provided by the bootloader and can't always be stored in a static
1904 DTB. To allow a device tree enabled kernel to be used with such
1905 bootloaders, this option allows zImage to extract the information
1906 from the ATAG list and store it at run time into the appended DTB.
1909 prompt "Kernel command line type" if ARM_ATAG_DTB_COMPAT
1910 default ARM_ATAG_DTB_COMPAT_CMDLINE_FROM_BOOTLOADER
1912 config ARM_ATAG_DTB_COMPAT_CMDLINE_FROM_BOOTLOADER
1913 bool "Use bootloader kernel arguments if available"
1915 Uses the command-line options passed by the boot loader instead of
1916 the device tree bootargs property. If the boot loader doesn't provide
1917 any, the device tree bootargs property will be used.
1919 config ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEND
1920 bool "Extend with bootloader kernel arguments"
1922 The command-line arguments provided by the boot loader will be
1923 appended to the the device tree bootargs property.
1928 string "Default kernel command string"
1931 On some architectures (EBSA110 and CATS), there is currently no way
1932 for the boot loader to pass arguments to the kernel. For these
1933 architectures, you should supply some command-line options at build
1934 time by entering them here. As a minimum, you should specify the
1935 memory size and the root device (e.g., mem=64M root=/dev/nfs).
1938 prompt "Kernel command line type" if CMDLINE != ""
1939 default CMDLINE_FROM_BOOTLOADER
1942 config CMDLINE_FROM_BOOTLOADER
1943 bool "Use bootloader kernel arguments if available"
1945 Uses the command-line options passed by the boot loader. If
1946 the boot loader doesn't provide any, the default kernel command
1947 string provided in CMDLINE will be used.
1949 config CMDLINE_EXTEND
1950 bool "Extend bootloader kernel arguments"
1952 The command-line arguments provided by the boot loader will be
1953 appended to the default kernel command string.
1955 config CMDLINE_FORCE
1956 bool "Always use the default kernel command string"
1958 Always use the default kernel command string, even if the boot
1959 loader passes other arguments to the kernel.
1960 This is useful if you cannot or don't want to change the
1961 command-line options your boot loader passes to the kernel.
1965 bool "Kernel Execute-In-Place from ROM"
1966 depends on !ARM_LPAE && !ARCH_MULTIPLATFORM
1968 Execute-In-Place allows the kernel to run from non-volatile storage
1969 directly addressable by the CPU, such as NOR flash. This saves RAM
1970 space since the text section of the kernel is not loaded from flash
1971 to RAM. Read-write sections, such as the data section and stack,
1972 are still copied to RAM. The XIP kernel is not compressed since
1973 it has to run directly from flash, so it will take more space to
1974 store it. The flash address used to link the kernel object files,
1975 and for storing it, is configuration dependent. Therefore, if you
1976 say Y here, you must know the proper physical address where to
1977 store the kernel image depending on your own flash memory usage.
1979 Also note that the make target becomes "make xipImage" rather than
1980 "make zImage" or "make Image". The final kernel binary to put in
1981 ROM memory will be arch/arm/boot/xipImage.
1985 config XIP_PHYS_ADDR
1986 hex "XIP Kernel Physical Location"
1987 depends on XIP_KERNEL
1988 default "0x00080000"
1990 This is the physical address in your flash memory the kernel will
1991 be linked for and stored to. This address is dependent on your
1994 config XIP_DEFLATED_DATA
1995 bool "Store kernel .data section compressed in ROM"
1996 depends on XIP_KERNEL
1999 Before the kernel is actually executed, its .data section has to be
2000 copied to RAM from ROM. This option allows for storing that data
2001 in compressed form and decompressed to RAM rather than merely being
2002 copied, saving some precious ROM space. A possible drawback is a
2003 slightly longer boot delay.
2006 bool "Kexec system call (EXPERIMENTAL)"
2007 depends on (!SMP || PM_SLEEP_SMP)
2011 kexec is a system call that implements the ability to shutdown your
2012 current kernel, and to start another kernel. It is like a reboot
2013 but it is independent of the system firmware. And like a reboot
2014 you can start any kernel with it, not just Linux.
2016 It is an ongoing process to be certain the hardware in a machine
2017 is properly shutdown, so do not be surprised if this code does not
2018 initially work for you.
2021 bool "Export atags in procfs"
2022 depends on ATAGS && KEXEC
2025 Should the atags used to boot the kernel be exported in an "atags"
2026 file in procfs. Useful with kexec.
2029 bool "Build kdump crash kernel (EXPERIMENTAL)"
2031 Generate crash dump after being started by kexec. This should
2032 be normally only set in special crash dump kernels which are
2033 loaded in the main kernel with kexec-tools into a specially
2034 reserved region and then later executed after a crash by
2035 kdump/kexec. The crash dump kernel must be compiled to a
2036 memory address not used by the main kernel
2038 For more details see Documentation/kdump/kdump.txt
2040 config AUTO_ZRELADDR
2041 bool "Auto calculation of the decompressed kernel image address"
2043 ZRELADDR is the physical address where the decompressed kernel
2044 image will be placed. If AUTO_ZRELADDR is selected, the address
2045 will be determined at run-time by masking the current IP with
2046 0xf8000000. This assumes the zImage being placed in the first 128MB
2047 from start of memory.
2053 bool "UEFI runtime support"
2054 depends on OF && !CPU_BIG_ENDIAN && MMU && AUTO_ZRELADDR && !XIP_KERNEL
2056 select EFI_PARAMS_FROM_FDT
2059 select EFI_RUNTIME_WRAPPERS
2061 This option provides support for runtime services provided
2062 by UEFI firmware (such as non-volatile variables, realtime
2063 clock, and platform reset). A UEFI stub is also provided to
2064 allow the kernel to be booted as an EFI application. This
2065 is only useful for kernels that may run on systems that have
2069 bool "Enable support for SMBIOS (DMI) tables"
2073 This enables SMBIOS/DMI feature for systems.
2075 This option is only useful on systems that have UEFI firmware.
2076 However, even with this option, the resultant kernel should
2077 continue to boot on existing non-UEFI platforms.
2079 NOTE: This does *NOT* enable or encourage the use of DMI quirks,
2080 i.e., the the practice of identifying the platform via DMI to
2081 decide whether certain workarounds for buggy hardware and/or
2082 firmware need to be enabled. This would require the DMI subsystem
2083 to be enabled much earlier than we do on ARM, which is non-trivial.
2087 menu "CPU Power Management"
2089 source "drivers/cpufreq/Kconfig"
2091 source "drivers/cpuidle/Kconfig"
2095 menu "Floating point emulation"
2097 comment "At least one emulation must be selected"
2100 bool "NWFPE math emulation"
2101 depends on (!AEABI || OABI_COMPAT) && !THUMB2_KERNEL
2103 Say Y to include the NWFPE floating point emulator in the kernel.
2104 This is necessary to run most binaries. Linux does not currently
2105 support floating point hardware so you need to say Y here even if
2106 your machine has an FPA or floating point co-processor podule.
2108 You may say N here if you are going to load the Acorn FPEmulator
2109 early in the bootup.
2112 bool "Support extended precision"
2113 depends on FPE_NWFPE
2115 Say Y to include 80-bit support in the kernel floating-point
2116 emulator. Otherwise, only 32 and 64-bit support is compiled in.
2117 Note that gcc does not generate 80-bit operations by default,
2118 so in most cases this option only enlarges the size of the
2119 floating point emulator without any good reason.
2121 You almost surely want to say N here.
2124 bool "FastFPE math emulation (EXPERIMENTAL)"
2125 depends on (!AEABI || OABI_COMPAT) && !CPU_32v3
2127 Say Y here to include the FAST floating point emulator in the kernel.
2128 This is an experimental much faster emulator which now also has full
2129 precision for the mantissa. It does not support any exceptions.
2130 It is very simple, and approximately 3-6 times faster than NWFPE.
2132 It should be sufficient for most programs. It may be not suitable
2133 for scientific calculations, but you have to check this for yourself.
2134 If you do not feel you need a faster FP emulation you should better
2138 bool "VFP-format floating point maths"
2139 depends on CPU_V6 || CPU_V6K || CPU_ARM926T || CPU_V7 || CPU_FEROCEON
2141 Say Y to include VFP support code in the kernel. This is needed
2142 if your hardware includes a VFP unit.
2144 Please see <file:Documentation/arm/VFP/release-notes.txt> for
2145 release notes and additional status information.
2147 Say N if your target does not have VFP hardware.
2155 bool "Advanced SIMD (NEON) Extension support"
2156 depends on VFPv3 && CPU_V7
2158 Say Y to include support code for NEON, the ARMv7 Advanced SIMD
2161 config KERNEL_MODE_NEON
2162 bool "Support for NEON in kernel mode"
2163 depends on NEON && AEABI
2165 Say Y to include support for NEON in kernel mode.
2169 menu "Userspace binary formats"
2171 source "fs/Kconfig.binfmt"
2175 menu "Power management options"
2177 source "kernel/power/Kconfig"
2179 config ARCH_SUSPEND_POSSIBLE
2180 depends on CPU_ARM920T || CPU_ARM926T || CPU_FEROCEON || CPU_SA1100 || \
2181 CPU_V6 || CPU_V6K || CPU_V7 || CPU_V7M || CPU_XSC3 || CPU_XSCALE || CPU_MOHAWK
2184 config ARM_CPU_SUSPEND
2185 def_bool PM_SLEEP || BL_SWITCHER || ARM_PSCI_FW
2186 depends on ARCH_SUSPEND_POSSIBLE
2188 config ARCH_HIBERNATION_POSSIBLE
2191 default y if ARCH_SUSPEND_POSSIBLE
2195 source "net/Kconfig"
2197 source "drivers/Kconfig"
2199 source "drivers/firmware/Kconfig"
2203 source "arch/arm/Kconfig.debug"
2205 source "security/Kconfig"
2207 source "crypto/Kconfig"
2209 source "arch/arm/crypto/Kconfig"
2212 source "lib/Kconfig"
2214 source "arch/arm/kvm/Kconfig"